Ricoh MP2500LN
Service Program Mode. SP1-XXX (Feed) 2
The following codes are used:
- Asterisk (*): The settings are saved in the NVRAM. Most of them return to the default values when you execute SP 5801-2
- The DFU menu is for design or factory use only. You must not change the settings.
- Brackets ([ ]): The brackets enclose the setting rage, default value, and minimum step (with unit) as follows: [Minimum to Maximum / Default / Step].
- SSP: The program is in the SSP Mode only. Consult your supervisor before you use this program.
SP1-XXX (Feed)
1106 | Display Fusing |
1106 1 | Displays the fusing temperature (center) |
1106 2 | Displays the fusing temperature (end) |
1107* | Fusing Soft Start | |
Adjusts the number of zero-cross cycles of the fusing lamp AC supply needed to bring the fusing lamp power to 100% while bringing the lamp up to the standby temperature or while copying. Increase this value if the machine is experiencing sudden power dropouts (* "Fusing Temperature Control" in the chapter "Detailed Section Descriptions"). | ||
1107 1 | Warm Up Soft Start | [0 = 10 cycles / 1 = 20 cycles / 2 = 50 cycles] |
1107 2 | Other Soft Start | [0 = 5 cycles / 1 = 10 cycles / 2 = 20 cycles] |
1108* | Set-Fusing Start | [0 = 1s / 1 = 1.5s / 2 = 2s] |
1108 1 | Specifies the interval for fusing-temperature control (* "Fusing Temperature Control" in the chapter "Detailed Section Descriptions"). |
1109 | Nip Band Check |
1109 1 | Checks the fusing nip band (* "NIP Band Width Adjustment" in the "Replacement and Adjustment"). |
1110* | Fan Control Timer |
1110 1 | [30 to 60 / 30 / 1 s/step] Inputs the fan control time. The fan maintains normal speed for the specified time after occurrence of an SC or following entry into Warm-up mode, Low Power mode, or Night/ Off mode. |
1159* |
Fusing Jam SC Code Setting |
[0=No / 1=Yes] |
1159 1 |
This SP mode detects SC559. Set this SP mode to 'Yes' if the machine experiences paper jam problems on a continual basis. |
1902 | Display-AC Freq. |
1902 1 | Displays the fusing lamp power control frequency (as detected by the zero cross signal generator). The displayed value is 1/5 the actual frequency: 10 = 50 Hz, 12 = 60 Hz. |
1903* | Feed Clutch Boost | |
Adjusts the amount of extra push that the feed clutch gives to the been corrected at registration. This feature helps the registration | paper after the skew has roller feed certain types | |
of paper (such as thick paper). Increase the value if thick paper is jamming after feeding from the registration roller. | ||
1903 1 | By-pass tray | [0 to 10 / 6 / 1 mm/step] |
1903 2 | 2nd, 3rd, 4th tray | [0 to 10 / 3 / 1 mm/step] |
1908* | Optional Tray Adj. | |
Adjusts the reverse time for the upper and lower paper lift motors. | ||
1908 1 | 1st optional | [-2 to 2 / 0 / 1/step] |
1908 2 | 2nd optional |
1911* | By-pass Envelope |
1911 1 | [0 = No / 1= Yes] The program dedicated to envelope printing runs when you enable this program (SP 1911-1) and you select "Thick Paper" as the paper type of the by-pass tray (System Settings > Tray Paper Settings > Paper Type: Bypass Tray). |