Ricoh MP2500LN
Service Program Mode. SP1-XXX (Feed) 1
The following codes are used:
- Asterisk (*): The settings are saved in the NVRAM. Most of them return to the default values when you execute SP 5801-2
- The DFU menu is for design or factory use only. You must not change the settings.
- Brackets ([ ]): The brackets enclose the setting rage, default value, and minimum step (with unit) as follows: [Minimum to Maximum / Default / Step].
- SSP: The program is in the SSP Mode only. Consult your supervisor before you use this program.
SP1-XXX (Feed)
1001* | Leading Edge Registration | |
Adjusts the printing leading-edge registration from paper trays. | ||
1001 1 | All Trays | [-9.0 to 9.0 / 0.0 / 0.1 mm/step] (* "Copy Adjustments Printing/Scanning") |
1001 2 | By-pass | |
1001 3 | Duplex |
1002* | Side-to-Side Registration | |
Adjusts the printing side-to-side registration from each paper feed station, using the Trimming Area Pattern (SP 5902, No.10). Adjustments are supported for all 4 possible feed trays (including optional trays). The SP 1002-1 setting is applied to all trays, not just the 1st tray. Settings for trays 2 to 4 are offsets relative to the SP 1002 1 setting. For duplex copies, the value for the front side is determined by SP 1002-1 to -4, and the value for the rear side is determined by SP 1002-6. |
||
1002 1 | 1st tray | [-9.0 to 9.0 / 0.0 / 0.1 mm/step] (* "Copy Adjustments Printing/Scanning") |
1002 2 | 2nd tray | |
1002 3 | 3rd tray | |
1002 4 | 4th tray | |
1002 5 | By-pass | |
1002 6 | Duplex |
1007 | Display By-pass | |
1007 1 | Display By-pass | Displays the by-pass paper width switch output. |
1103* | Fusing Idling | |
This program decides the action of the Fusing Drive Release Mechanism. When you select "1," the contact/release control is disabled and the drive power is always transmitted to the fusing unit. As a result, the machine takes a longer time to warm up the fusing unit. Use SP 1103-1 if fusing quality is low even when the room temperature is not very low. | ||
1103 1 | Fusing Idling | [0 = No / 1 = Yes] |
1105* | Fusing Temperature Adjustment | |
Adjusts the target fusing temperature. "Center" indicates the center of the roller; "End" indicates the front and rear ends. | ||
1105 1 | Warm Up-Center | [140 to 180 / 170 / 1°C/step] |
1105 2 | Warm Up-End | |
1105 3 | Standby-Center | [140 to 170 / 165 / 1°C/step] |
1105 4 | Standby-End | [140 to 165 / 165 / 1°C/step] |
1105 5 | Copying-Center | [140 to 165 / 165 / 1°C/step] |
1105 6 | Copying-End | |
1105 7 | Low Level 2-Center | [0 to 80 / 60 / 1°C/step] |
1105 8 | Low Level 2-End | |
1105 9 | Thick-Center | [140 to 185 / 185 / 1°C/step] |
1105 10 | Thick-End | |
1105 11 | Warm Up Low-Center | [140 to 180 / 180 / 1°C/step] |
1105 12 | Warm Up Low-End | |
1105 13 | Copy-Low-Center | [140 to 185 / 185 / 1°C/step] |
Adjusts the target fusing temperature for the center of the roller when the inside temperature of the machine is 18C or less. | ||
1105 14 | Copy-Low-End | [140 to 185 / 185 / 1°C/step] |
Adjusts the target fusing temperature for the end of the roller when the inside temperature of the machine is 18C or less. | ||
1105 15 | Low-Temp-Time-1 | [0 to 60 / 60 / 1 second/step] |
Adjusts the threshold time for the 1st temperature decrement. When the time of the first copy/print reaches this threshold, the target temperature is decreased by 5°C from the temperature specified with SP1105-13, -14. | ||
1105 16 | Low-Temp-Time-2 | [61 to 120 / 120 / 1 second/step] |
Adjusts the threshold time for the 2nd temperature decrement. When the time of the first copy/print reaches this threshold, the target temperature is decreased by 10°C from the temperature specified with SP1105-13, -14. | ||
1105 17 | Low-Temp-Time-3 | [121 to 240 / 240 / 1 second/step] |
Adjusts the threshold time for the 3rd temperature decrement. When the time of the first copy/print reaches this threshold, the target temperature is decreased by 15°C from the temperature specified with SP1105-13, -14. |