Lexmark 7562-432 X792de

1. Open the left access door.
2. Firmly grasp the jammed paper, and then gently pull it out.
   Note: Make sure all paper fragments are removed.
3. Close the door.
4. From the operator panel, touch Continue, jam cleared.

Additional checks—200 paper jam

Error code	Description	Action
200.01	Input sensor is made when printer powers up or covers are closed. Possible causes: Paper jam leaving page over sensor Defective input sensor Faulty system board	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “Input, S1, narrow media, and near narrow media sensor service check” .
200.02	Paper hit the input sensor too soon. Possible causes: Damaged input sensor flag or input sensor Loose input sensor	Clear away anything in the paper path that might cause the paper to jam. The input sensor may not be functioning properly. Go to “200.02—Paper Jam error service check” .
200.03	Input sensor is never made or made late. Possible causes: Faulty input sensor Faulty staging deflector assembly Faulty autocomp assembly	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “200.03, 200.08—Paper Jam error service check” .
200.04	Input sensor flag broke early. Possible cause: Incorrect paper settings Faulty input sensor Faulty system board	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. Go to “Input, S1, narrow media, and near narrow media sensor service check” .
200.05, 200.07	Input sensor does not break or breaks late. Possible causes: Incorrect paper settings Incorrect paper loading Incorrect paper guide setting ITU module failure Lower guide failure Paper pick mechanism failure Input sensor failure	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. Flex the media, and stack it flat in the paper tray. Properly set the paper guides in the paper tray. Check the pick roll tires, and replace them if they are worn. Go to “200.05, 200.07—Paper Jam error service check” on page 2-104.
200.08	Input sensor is never made or made late.	See “200.03” .
200.21, 200.22	Staging motor stalled or is under speed. Possible causes: Faulty staging motor Faulty cable/connector Faulty system board	Check that the waste toner container is latched correctly in the printer. Check for anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “147.xx—Staging motor error service check” .
200.31	Near narrow media sensor is made when the printer tries to print from an idle state. Possible causes: Paper jam leaving paper over the sensor Defective near narrow media sensor Faulty system board	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “Input, S1, narrow media, and near narrow media sensor service check” .
200.32	Near narrow media sensor is never made or is made late. Damaged narrow media flag or narrow media sensor Loose input sensor	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “200.32—Paper Jam error service check” .
200.33	Near narrow media sensor is never made or is made late. Faulty input sensor Faulty staging deflector assembly Faulty autocomp assembly	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “200.33, 200.38—Paper Jam error service check” .
200.34	Near narrow media sensor broke early. Possible causes: Incorrect paper settings Defective near narrow media sensor	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. Go to “Input, S1, narrow media, and near narrow media sensor service check” .
200.35, 200.37	Near narrow media sensor does not break or breaks late. Incorrect paper settings Incorrect paper loaded Incorrect paper guide setting ITU module failure Lower guide failure Paper pick mechanism failure Near narrow media sensor failure	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. Flex the media, and stack it flat in the paper tray. Properly set the paper guides in the paper tray. Check the pick roll tires, and replace them if they are worn. • Go to “200.35, 200.37—Paper Jam error service check” .
200.38	Near narrow media sensor is never made or is made late.	See “200.33” .
200.40	S1 sensor is made early. Possible causes: Incorrect paper settings Defective S1 sensor	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. If clearing a paper jam does not fix the problem, go to “241.02—Paper Jam error service check” .
200.41	Narrow media sensor is made when printer tries to print from an idle state. Possible causes: Paper jam leaving page over sensor Defective narrow media sensor Faulty system board	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “Input, S1, narrow media, and near narrow media sensor service check” .
200.42	Narrow media sensor is made early. Possible causes: Incorrect paper settings Defective narrow media sensor	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. If clearing a paper jam does not fix the problem, go to “200.42—Paper Jam error service check” .
200.43	Narrow media sensor is never made or is made late.	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “200.43, 200.48—Paper Jam error service check” .
200.44	Narrow media sensor broke early. Possible causes: Incorrect paper settings Defective narrow media sensor	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. Go to “Input, S1, narrow media, and near narrow media sensor service check” .
200.45	Narrow media sensor does not break or breaks late. Incorrect paper settings Incorrect paper loaded Incorrect paper guide setting ITU module failure Lower guide failure Paper pick mechanism failure Narrow media sensor failure	Clear away anything in the paper path that might cause the paper to jam. Be sure the paper settings match the media. Flex the media, and stack it flat in the paper tray. Properly set the paper guides in the paper tray. Check the pick roll tires, and replace them if they are worn. Go to “200.45, 200.47—Paper Jam error service check”.
200.47	Narrow media sensor does not break or breaks late.	See “200.45” .
200.48	Narrow media sensor is never made or is made late.
200.49	S1 sensor is made when printer tries to print from an idle state. Possible causes: Paper jam leaving paper over the sensor Defective near narrow media sensor Faulty system board	Clear away anything in the paper path that might cause the paper to jam. If clearing a paper jam does not fix the problem, go to “Input, S1, narrow media, and near narrow media sensor service check” .