Kyocera ECOSYS P8060cdn
Troubleshooting. Abnormal Noise 1
1. Abnormal noise (Basic support)
Step | Check description | Assumed cause | Measures |
---|---|---|---|
1 | Applying the grease | The grease on each gear or bushing is not enough. | Check the rotation of the roller, the pulley or the gear, if they do not rotate smoothly, apply the grease on the gears or the bearings. (EM-50LP, Part number: 7BG010009H) |
2 | Reattaching the gears or the bearings | The parts such as each gear or bushing are not properly attached. | Reattach the gear or the bearings. |
2. Abnormal sounds from the paper conveying section
Frictional wear, smudges / foreign objects adhesion on the conveying rollers, pulleys and the gears
Step | Check description | Assumed cause | Measures |
---|---|---|---|
1 | Cleaning and applying the grease | The bushing or the gear is dirty or foreign objects are on them. | Clean the bearings and the gears of the conveying related rollers, and apply the grease (EM-50LP, Part number: 7BG010009H). |
2 | Cleaning and applying the grease | The inside of the pulley is worn down. | Clean the drive shaft of the conveying related pulley and apply the Hanarl. (302LV94550) |
3 | Cleaning and applying the grease | The gear tooth are dirty or foreign objects are on them. | Clean the drive gears of the conveying related rollers, and apply the grease (EM-50LP, Part number: 7BG010009H) |
4 | Checking the pressure spring | Pressure of the conveying related roller and pulley are weak, and the bearing vibrates as the roller and pulley rotate. | Reattach the pressure springs of the conveying related rollers or the pulleys, or replace them. |
5 | Replacing the feed drive unit | The parts in the feed drive unit are faulty. | Replace feed drive unit. |
3. Abnormal sound from the developer section
Caused by the developer unit.
Step | Check description | Assumed cause | Measures |
---|---|---|---|
1 | Executing U030 (color models) | (Specify the developer unit which is faulty.) | Specify the faulty developer unit by executing U030. (Go to the next step.) |
2 | Checking the developer unit | The developer unit drive is faulty. | Check if the developer is not leaking from the developer unit, there is no damaged location, and whether the roller rotates manually. Repair if necessary. |
3 | Developer unit replacement | The developer unit is faulty. | Replace the developer unit. |
4. Abnormal sound from the eject section
Smudges / foreign objects adhesion in the eject section
Step | Check description | Assumed cause | Measures |
---|---|---|---|
1 | Cleaning and applying the grease | Conductive bearings located at behind the lower exit roller of the main unit slide with the roller shaft. (abnormal sound) | Apply Hanarl (302LV94550) to the conductive bearing (black) at the machine rear side of the exit lower roller. |
2 | Checking the drive link gear | The engagement of the drive coupling gear of the fuser unit and the exit unit is strong and the exit actuator vibrates. | Fix the drive side of the exit unit to the lower side with screw so that the meshing of the drive coupling gear between the fuser unit and the exit unit becomes proper |
3 | Cleaning and applying the grease | The bearings or gears are dirty or the foreign objects adhere. | Clean the bearings of the upper exit roller and the gears, and apply the grease. (EM-50LP, Part number: 7BG010009H) |
4 | Cleaning and applying the grease | The bearings are dirty or the foreign objects adhere. | Clean the shaft of the exit upper pulley and the exit lower pulley, and apply Hanarl (302LV94550). |
5 | Cleaning and applying the grease | The bearings are dirty or the foreign objects adhere. | Clean the reverse guide and the shaft of the exit feedshift guide. If it is not possible to remove the dirt or the foreign objects, replace them. |
6 | Checking the exit reverse motor | The exit reverse motor is faulty. | Execute U030 [Exit]. If the abnormal sound occurs, replace the exit reverse motor. |