Konica-Minolta bizhub PRESS 1250P
Adjustment after replacing parts
Priority for Adjustment/Setting after replacing parts
Conduct the following adjustment on the items list in this order when replacing the parts on the list. Proper operation/image quality is not guaranteed without conducting those adjustment after the parts replacement.
Note
- When replacing the image processing board (IPB) due to the IPB being damaged, be sure to use the NVRAM board (NRB) that was installed on the damaged IPB on the new IPB. Contact the service manager of the authorized distributor if it is considered that NRB is also damaged.
- The NVRAM board (NRB) stores various adjustment data, setting data and counter data. Therefore, when replacing the PB, perform all adjustments and settings, and be sure to replace the parts for control correction (Drum, developer, cleaning blade, cleaning web). For details, contact the service manager of the authorized distributor.
- When replacing a board due to PB control board (PBCB), SD control board (SDCB), FD control board (FDCB), RU control board (RUCB) or FNS control board (FNSCB) being damaged, be sure to use the non-volatile memory (EEPROM) that was installed on the damaged control board on the new control board. Install the new EEPROM and perform all adjustments for the PB, SD, FD, RU or FS if it is considered that the EEPROM is also damaged.
Classification | Replacement parts | Description |
---|---|---|
− | After PM Implementation | PM cycle setting counter reset |
Drum | Drum | Setting powder application Charging Potential Auto. Adj. Sensitive Drum set Mode Auto Maximum Density adjustment Auto Dot Diameter adjustment Cartridge Set Mode |
Development | Developer | Charging Potential Auto Adj. TonerDenditySensorInit.Auto Auto Maximum Density adjustment Cartridge Set Mode |
Cleaning | Cleaning blade | Setting powder application Blade Replacement spring charge Blade setting mode Cartridge Set Mode |
Toner guide brush | Setting powder application | |
Process mount | Drum + Developer | Setting powder application Charging Potential Auto Adj. Sensitive Drum set Mode TonerDenditySensorInit.Auto Auto Maximum Density adjustment Auto Dot Diameter adjustment Cartridge Set Mode |
Drum + Cleaning blade | Setting powder application Blade auto replacement spring charge Blade Setting Mode Charging Potential Auto Adj. Sensitive Drum set Mode Auto Maximum Density adjustment Auto Dot Diameter adjustment Cartridge Set Mode |
|
Developer + Cleaning blade | Setting powder application Blade auto replacement spring charge Blade Setting Mode TonerDenditySensorInit.Auto Auto Maximum Density adjustment Auto Dot Diameter adjustment Cartridge Set Mode |
|
Scanner | Slit glass | ADF Density Adjustment |
Scanner wire, Exposure/Mirror unit | Mirror unit positioning (require the jigs) Scanner Restart Timing adjustment Distortion adjustment original glass (main scan direction) Distortion adjustment original glass (sub scan direction) Distortion adjustment ADF (main scan direction) Distortion adjustment ADF (sub scan direction) |
|
CCD unit | Printer CD-Mag. Adj.(Side1) Scanner paper feed direction magnification adjustment Scanner (ADF) paper feed direction magnification adjustment Scanner restart timing adjustment Distortion adjustment original glass (main scan direction) Distortion adjustment original glass (sub scan direction) Distortion adjustment ADF (main scan direction) Distortion adjustment ADF (sub scan direction) CCD Right and Left Quality Adjustment |
|
Write | LPH unit | Printer CD-Mag. Adj.(Side1) Printer Centering Adjustment Printer Restart Timing Adjustment(Side1) Auto charging potential adjustment Auto maximum density adjustment Auto dot diameter adjustment Cartridge set mode |
Registration | Registration roller | Regist line speed adjustment Printer FD-Mag. Adjustment (Side1) Printer Restart Timing Adjustment(Side1) |
Fusing Cleaning |
Cleaning web | Fusing cleaning web counter clear |
Fusing heater lamp /1 (L1) | Installing direction of fusing lamp (with maker mark in front) | |
Fusing heater lamp /2 (L2) | Installing direction of fusing lamp (with maker mark in front) | |
Fusing heater lamp /3 (L3) | Installing direction of fusing lamp (with maker mark in front) | |
Thermostat /1 (TS1), /2 (TS2) | Thermostat positioning (require the jig) | |
Thermostat /3 (TS3) | Thermostat positioning (require the jig) | |
Boards | High voltage unit /1, /2 (HV1, /2) | High voltage auto adjustment |
Overall control board (OACB) | Rewriting of firmware NVRAM board (NRB) replacement |
|
Printer control board (PRCB) | Rewriting of firmware | |
Operation board /1 (OB1) | Rewriting of firmware | |
Hard disk /2 (HDD2) | IC HDD format | |
ADU drive board /1 (ADUDB1) | Multi feed detection board adjustment | |
Controller SSD | Rewriting of firmware | |
DF-615 /616 | DF control board (DFCB) | Rewriting of firmware ADF Sensor Sensitivity adjustment ADF Centering Sensor Adj. ADF Original Size Adj. ADF Registration Loop adjustment Scanner (ADF) paper feed direction magnification adjustment ADF Restart Timing adjustment ADF Centering adjustment ADF Skew Offset adjustment Distortion adjustment ADF (main scan direction) Distortion adjustment ADF (sub scan direction) |
FA-501 | FA-501 multi feed detection board (MFDB) | Multi feed detection board adjustment |
EF-102 | Cleaning web | Fusing cleaning web counter clear |
Fusing heater lamp /1 (L1) | Installing direction of fusing lamp (with maker mark in front) | |
Fusing heater lamp /2 (L2) | Installing direction of fusing lamp (with maker mark in front) | |
Fusing heater lamp /3 (L3) | Installing direction of fusing lamp (with maker mark in front) | |
Thermostat /1 (TS1), /2 (TS2) | Thermostat positioning (require the jig) | |
Thermostat /3 (TS3) | Thermostat positioning (require the jig) | |
RU-509/510 | RU control board (RUCB) | EEPROM replacement Rewriting of firmware |
ZU-608 | ZU control board (ZUCB) | Punch Edge Sensor Adjustment |
Paper edge sensor board (PESB) | Punch Edge Sensor Adjustment | |
FS-532 | FNS control board (FNSCB) | EEPROM replacement Rewriting of firmware |
SD-510 | SD control board (SDCB) | Rewriting of firmware |
Stapler unit | Clincher positioning (require the jig) | |
PK-522 | Punch drive board (PDB) | Paper Edge Sensor Adjustment |
Paper size sensor (PS305) | Paper Edge Sensor Adjustment | |
LS-505 | LS control board (LSCB) | Toggle switch setting Rewriting of firmware Grip conveyance home sensor adjustment Paper width adjustment Paper length adjustment |
FD-503 | FD control board (FDCB) | DIPSW setting of the boards Rewriting of firmware EEPROM replacement |
Multi feed detection board (MFDB) | Multi feed detection board adjustment | |
PI drive board (PIDB) | Multi feed detection board adjustment | |
PB-503 | PB control board (PBCB) | DIPSW setting of the boards Rewriting of firmware EEPROM replacement Multi feed detection board adjustment |
Multi feed detection board (MFDBS, MFDBR) | Multi feed detection board adjustment |