Konica-Minolta bizhub C224e
Service Mode. Adjustment after replacing
| Replacement part/Service job | Adjustment/setting items |
|---|---|
| Replace feed roller, pick-up roller, separation roller (tray 1, tray 2) | [Service Mode] / [Counter] / [Life] / [Counter Clear] |
| Replace feed roller, separation roller assy | [Service Mode] / [Counter] / [Life] / [Counter Clear] |
| Install LCT (Built-in) | [Service Mode] / [System2] / [LCT (Built-in) Size Settings] 1 [Service Mode] / [Machine] / [Printer Area] / [Printer Image Centering Side 1] 2 [Service Mode] / [Machine] / [Printer Area] / [Prt. Image Center. Side 2 (Dup)] 3 [Service Mode] / [Machine] / [Printer Area] / [Tray Printing Position: Tip] 4 |
| Install LCT | [Service Mode] / [Machine] / [Printer Area] / [Printer Image Centering Side 1] |
| Replace CCD unit | [Service Mode] / [System2] / [CCD Calibration] 1 [Service Mode] / [System2] / [Line Mag Setting] 2 [Service Mode] / [Machine] / [Printer Area] / [Paper Feed Direction Adj.] 3 [Service Mode] / [Machine] / [Scan Area] / [Main Scan Zoon Adj.] 4 [Service Mode] / [Machine] / [Scan Area] / [Scanner Image Side Edge] 5 |
| Replace developing unit | [Service Mode] / [Imaging Process Adjustment] / [Gradation Adjust] |
| Replace drum unit | [Service Mode] / [Imaging Process Adjustment] / [Gradation Adjust] |
| Replace transfer belt unit | [Service Mode] / [Counter] / [Life] / [New Release] 1 [Service Mode] / [Imaging Process Adjustment] / [Gradation Adjust] 2 |
| Replace PH unit | [Service Mode] / [Machine] / [Print Head Skew Adj.] / [Print Head Skew Reset] 1 [Service Mode] / [Machine] / [Printer Area] / [Leading Edge Adjustment] 2 [Service Mode] / [Machine] / [Printer Area] / [Printer Image Centering Side 1] 3 |
| Replace original size detection sensor | Installation of original size sensor 1 [Service Mode] / [State Confirmation] / [Table Number] 2 |
| Replace scanner motor | Scanner motor belt adjustment |
| Replace scanner home sensor | [Service Mode] / [Machine] / [Scan Area] / [Image Position: Leading Edge] |
| Replace printer control board | Installing the firmware 1 [Service Mode] / [Enhanced Security] / [Engine Data Backup] 2 |
| Replace MFP board | Entering the machine type information 1 Installing the firmware 2 Restore (backup) data 3 [Service Mode] / [Imaging Process Adjustment] / [Gradation Adjust] 4 |
| Replace SSD board | Installing the firmware. |
| Replace original glass | [Service Mode] / [Machine] / [Scan Area] / [Scanner Image Side Edge] 1 [Service Mode] / [Machine] / [Scan Area] / [Image Position: Leading Edge] 2 |
| Replace hard disk | [Service Mode] / [State Confirmation] / [Memory/HDD Adj.] / [HDD Format] 1 [Service Mode] / [State Confirmation] / [Memory/HDD Adj.] / [HDD R/W Check] 2 Install Data 3 |
| Replace control panel unit | Touch panel calibration |
| Replace DF control board | Installing the firmware 1 [Service Mode] / [ADF] / [Original Tray Width] 2 [Service Mode] / [ADF] / [Mixed original Size adjustment] 3 |
| Add key counter | Re-entry of Enhanced Security settings |
| Execute initialize | [Service Mode] / [System 2] / [HDD Installed] 1 Re-entry of Utility settings 2 [Service Mode] / [System 1] / [Serial Number] 3 [Service Mode] / [System 1/2] and re-entry of setting values 4 Re-entry of Enhanced Security settings 5 |
| Add an optional device | [Service Mode] / [Firmware Version] |
| Execute F/W update | [Service Mode] / [Firmware Version] |
| Add fax board | [Service Mode] / [System2] / [Option Board Status] 1 Installing the firmware 2 [Service Mode] / [System1] / [Marketin Area] / [Fax Target] 3 |
| Replace DF-701 | ADF adjusting the height 1 Adjusting front side skew feed on ADF 2 Adjusting back side skew feed on ADF 3 [Service Mode] / [ADF] / [Original Tray Width] 4 [Service Mode] / [ADF] / [Original Stop Position] 5 [Service Mode] / [ADF] / [Feed Zoom] 6 [Service Mode] / [ADF] / [FD-Mag. ADJ. (B)] 7 [Service Mode] / [ADF] / [Main Scanning Direction Zoom] 8 [Service Mode] / [ADF] / [Read Pos Adj] 9 [Service Mode] / [System 2] / [CIS Image Adjustment] 10 |
| Replace CIS module | Adjusting back side skew feed on ADF 1 [Service Mode] / [ADF] / [Feed Zoom] 2 [Service Mode] / [ADF] / [FD-Mag. ADJ. (B)] 3 [Service Mode] / [ADF] / [Auto Stop Position Adjustment] 4 [Service Mode] / [ADF] / [Main Scanning Direction Zoom] 5 [Service Mode] / [ADF] / [Read Pos Adj] 6 [Service Mode] / [System 2] / [CIS Image Adjustment] 7 |