PrintCopy.info service

Canon iR Advance 6065i

 All About this machine
Table Of Contents 

Troubleshooting. Alarm Code 4

Alarm
Code		 Title A. movement /B. cause /C. measures
31-0008 HDD failure prediction alarm Movement: HDD failure is expected to occur in a short time due to occurrence of physical error in HDD. It does not occur in the HDD of mirroring configuration.
Cause: Error in the S.M.A.R.T. value of HDD
Measures:
  1. Back up the data stored in HDD.
  2. Replace the HDD.
  3. Restore the data.
S.M.A.R.T. (Self-Monitoring Analysis and Reporting
Technology): Self-diagnosis function built in the HDD. The occurrence rate of reading error, reading and writing speed, the total number of Motor start-up and stop times, the total length of power-on time, etc. are monitored.
32-0002 Potential control (VL control) error Movement: Not reflecting the result of VL control. To the laser power determined with VL control, the power with which the previous potential control was succeeded (within target potential +/-10V) is applied.
Cause: The measured value in the dark area (VL) differs over +/-10V but less than +/-30V than the target potential at potential control.
Measures: If there is no influence on image, measures are not needed. If not, execute the following measures.
  1. Check the installation of the Pre-exposure LED (connector connection, open circuit, the caught cable).
  2. Check the installation of the Primary Charging Assembly (connector connection, open circuit, the caught cable).
  3. Check the fixation state of the Drum and the Drum Shaft (check if the drum fixation cylinder is properly installed).
  4. Check if the Dustproof Glass is soiled. If necessary, clean it.
  5. Check the installation of the Laser Scanner Unit (connector connection, open circuit, the caught cable).
  6. Check the installation and connection of the Primary Charging High Voltage PCB (PCB11) (connector connection, open circuit, the caught cable).
  7. Check the installation of the Potential Sensor (connector connection, open circuit, the caught cable).
  8. Check the installation and connection of the Drum Motor (M1) (connector connection, open circuit, the caught cable).

Replace the parts.

  • Primary Charging Assembly
  • Laser Scanner Unit
  • Potential Sensor
  • Primary Charging High Voltage PCB (PCB11)
  • Drum Motor (M1)
  • Main Driver PCB (PCB2)
  • DC Controller PCB (PCB1)
Alarm
Code		 Title A. movement /B. cause /C. measures
33-0001 Delivery Assembly Decurler Fan alarm Movement: No change.
Cause: Connector disconnection of the Paper Cooling Fan (FM5).
Failure of the Paper Cooling Fan (FM5).
Measures: Check the connector -> Replace the Paper Cooling Fan (FM5).
33-0002 Feed Fan alarm Movement: No change.
Cause: Connector disconnection of the Registration Motor/ Duplex Motor Cooling Fan (FM42).
Failure of the Registration Motor/Duplex Motor Cooling Fan (FM42).
Measures: Check the connector -> Replace the Registration Motor/Duplex Motor Cooling Fan (FM42).
33-0010 Stream Reading Fan alarm Movement: Nothing in particular (Fan stops).
Cause: The Fan rotation signal cannot be detected after 3 seconds have passed since the Scanner Unit Heat Exhaust Fan (FM1) is turned ON.
Measures: Check the connector connection -> Replace the Scanner Unit Heat Exhaust Fan (FM1).
33-0013 Power Unit Fan 1 alarm Movement: No change.
Cause: Connector disconnection of the Feed Driver Cooling
Fan (FM40).
Failure of the Feed Driver Cooling Fan (FM40).
Measures: Check the connector -> Replace the Feed Driver Cooling Fan (FM40).
33-0022 Read Motor Cooling Fan alarm Movement: Nothing in particular (Fan stops).
Cause: The Fan rotation signal cannot be detected after 3 seconds have passed since the Motor Driver Cooling
Fan (FM1) or the Read Motor Cooling Fan (FM2) is turned ON.
Measures: Check the connector connection -> Replace the
Motor Driver Cooling Fan (FM1) or the Read Motor Cooling Fan (FM2).
33-0023 Scanner Unit (DADF) Cooling Fan alarm Movement: Nothing in particular (Fan stops).
Cause: The Fan rotation signal cannot be detected after 3
seconds have passed since the (DADF) Scanner Unit Cooling Fan (FM3) is turned ON.
Measures: Check the connector connection -> Replace the DADF Scanner Unit Cooling Fan (FM3).
33-0025 Scanner Unit (Reader) Cooling Fan alarm Movement: Nothing in particular (Fan stops).
Cause: The Fan rotation signal cannot be detected after 3
seconds have passed since the (Reader) Scanner Unit Cooling Fan (FM2) is turned ON.
Measures: Check the connector connection -> Replace the (Reader) Scanner Unit Cooling Fan (FM2).
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us