Description: Static Jam BSD-Reference: CH 5.6. At power on, the control logic detected either the Platen Interlock is close when the Feeder Cover is open or the Feeder Cover Interlock is close when the Platen Interlock is open.
Remedy: If this occurs frequently, confirm if there is any interferance with the Feed Sensor (PL 13.9), the Document Registration Sensor (PL 13.7) or the Exit/Invert Sensor (PL 13.7). Check the sensor connectors for prober connection. Replace one sensor at a time until the problem is solved.
Code: 062-300
Description: Platen Interlock Open BSD-Reference: CH 5.6. Detected the opened Platen Interlock.
Remedy: Ensure that the DADF can be closed normally. The DADF can be closed normally. Y↓N→Remove obstructions or repair the DADF Counter Balances. Check that the Platen Interlock is functioning properly. The Platen Interlock is functioning properly. Y↓N→Replace the Platen Interlock Sensor. Replace the SLCC PWB (AIOC/Network PWB). (PL 8.1)
Code: 062-345
Description: IISS EEPROM Failure BSD-Reference: CH 3.1. Error in writing on or communicatiing with the EEPROM.
Remedy: Switch off the machine power then switch on the power. The problem is solved. Y↓N→Replace the SLCC PWB (AIOC/Network PWB). (PL 8.1) Problem is resolved.
Code: 062-360
Description: Carriage Position Fail BSD-Reference: CH 6.2. Detected no input of Regi Sensor when carriage was working or detected the failure of the Regi Sensor position, or detected the failure of the IIT Regi Sensor level.
Remedy: Check that the Lamp Carriage can move freely and has no loose cables. The Lamp Carriage and cables are good. Y↓N→Repair the Lamp Carriage. Enter the Diagnostic Mode. Enter Component Control Code [62-212]. Check the operation of the IIT Regi Sensor. The Regi Sensor is good. Y↓N→Reseat the Regi Sensor connector. Check the wiring for proper operation and repair if necessary. Replace the Regi Sensor. (PL 10.6) Enter the Diagnostic Mode. Enter Component Control Code [05-22]. The Carriage moves in the scan direction. Y↓N→Check the connector of the Carriage Motor and repair if necessary. Replace the Carriage Motor. (PL 10.6) Replace the SLCC PWB (AIOC/Network PWB). (PL 8.1)
Code: 062-371
Description: Lamp Illumination Fail BSD-Reference: CH 6.1. Detected incufficient light provided from the Lamp to the CCD.
Remedy: Check for any obstructions in the optical path between the lamp, the lens or the mirror. The optical path is clear of any obstructions. Y↓N→Remove the obstuctions. Check that the White Color Correction Plate (Reflector) is in place and not deterioarated. (PL 10.6) The White Color Correction Tape is good. Y↓N→Clean or replace the White Color Correction Plate. (PL 10.6) Enter the Diagnostic Mode. Enter Component Control Code [62-02]. The Illumination Lamp is good. Y↓N→Check that the Lamp harness is properly connected and repair if necessary. Replace the Illumination Lamp. Replace the SLCC PWB (AIOC/Network PWB). (PL 8.1)
Code: 062-380
Description: AGC Failure BSD-Reference: CH 6.2. Control logic has detected insufficient light from the Illumination Lamp during AGC (Automatic Gain Congrol) of the auto IIT Calibration at Start.
Remedy: Check for any obstructions in the optical path. Clean the Mirror, lens and the white balance strip. Switch off the power then switch it on again. The problem has been resolved. Y↓N→Enter the Diagnostic Mode. Enter Component Control Code [62-02]. The lamp is good. Y↓N→Check that the Lamp harness is properly connected and repair if necessary. Replace the Illumination Lamp. Replace the SLCC PWB and (3) EEPROMS (AIOC/Network PWB). (PL 8.1) POPO the machine and retry.