Xerox Phaser 6700

• Code: 09-000-00
• Description: Laser Failure A Laser Unit failure was detected. • 09-000-00 Laser Failure
• Causes: • Laser Unit, PL5.2.1 • MCU Board, PL10.2.18 • Rear Interlock Switch, PL1.3.6
• Remedy: 1 Test the Laser Unit motor using dc330 (061-001). The Laser Unit is operational. Go to Step 7. Go to Step 2. 2 Remove the Rear Cover to check the Rear Interlock Switch. The switch is operational. Go to Step 3. Replace the switch. 3 Check P/J701 on the IP Board. The connection is secure. Go to Step 4. Secure the connection. 4 Check P/J303 on the LVPS. The connection is secure. Go to Step 5. Secure the connection. 5 Check PJ151, PJ152 and PJ153 on the Laser Unit. The connections are secure. Go to Step 6. Secure the connections. 6 Check P/J3 on the MCU Board. The connection is secure. Go to Step 7. Secure the connection. 7 Replace the Laser Unit. Does the error persist? Replace the MCU Board. Complete.

• Code: 09-600-00, 09-601-00
• Description: Waste Cartridge is Full / Near Full The Waste Toner Full Sensor indicates the cartridge is full or nearly full. • 09-600-00 Waste Cartridge is Near Full • 09-601-00 Waste Cartridge is Full
• Causes: • Procon Assy, PL5.3.1 • Waste Toner Full Sensor PL5.3.13 • Exit Harness, PL11.1.7 • MCU Board, PL10.2.18
• Remedy: 1 Reseat the Waste Toner Cartridge. The error persists. Go to Step 2. Complete. 2 Test the Waste Toner Full Sensor using dc330 (091-001). The signal changes (On/Off). Go to Step 3. Go to Step 4. 3 Check continuity of the Exit Harness between P/J16 on the MCU Board and P/J106 at the sensor. The harness is undamaged. Go to Step 4. Replace the Exit Harness. 4 Check for 5V at P/J16-6 on the MCU Board. Is 5V available at P/J16-6? Replace the Waste Toner Full Sensor. Go to Step 5. 5 Replace the Procon Assy. The error persists. Replace the MCU Board. Complete

• Code: 09-602-00 ... 09-605-00
• Description: CMYK Toner is Low or Empty The Toner CRUM indicates the Toner Cartridge is low or empty. • 09-602-00 Cyan Toner is Low • 09-603-00 Magenta Toner is Low • 09-604-00 Yellow Toner is Low • 09-605-00 Black Toner is Low
• Causes: • Toner Cartridge (Y), PL6.1.1 • Toner Cartridge (M), PL6.1.2 • Toner Cartridge (C), PL6.1.3 • Toner Cartridge (K), PL6.1.4 • CRUM Connector Assy, PL6.1.10 • MCU Board, PL10.2.18 • Toner CRUM Harness, PL11.1.1
• Remedy: • Replace the affected Toner Cartridge. • Cycle system power. • If the problem persists, follow the procedure below.
  1 Reseat the indicated Toner Cartridge. The error persists. Go to Step 2. Complete. 2 Check connections between P/J11 on the MCU Board and indicated CRUM Connector: P/J204(Y), P/J205 (M), P/J206(C), P/J207 (K). The connection is secure. Go to Step 3. Secure the connection. 3 Check Toner CRUM Harness continuity between P/J11 on the MCU Board and indicated CRUM Connector: P/J204(Y), P/J205 (M), P/ J206(C), P/J207 (K). The harness is undamaged. Go to Step 4. Replace the Toner CRUM Harness. 4 Check for 2.5V at P/J11-3(Y), -7(M), - 11(C), -15(K) on the MCU Board. Is 2.5V available to the indicated Toner CRUM? Replace the affected Toner Cartridge. Replace the MCU Board.

• Code: 09-607-00, 09-613-00, 309.633.00
• Description: Maintenance Kit is Near/Past End of Life Maintenance Kit counter indicates the Transfer Belt, Transfer Roller and Feed Rollers have reached end of service. • 09-607-00 Maintenance Kit is Near End of Life • 09-613-00 Maintenance Kit is Past End of Life • 309.633.00 Maintenance Kit is Past End of Life
• Causes: • Maintenance Kit, PL5.1.99 • MCU Board, PL10.2.18
• Remedy: • Replace the Maintenance Kit. • Cycle system power. • If the problem persists, follow the procedure below.
  1 Reset the Maintenance Kit counter in the Reset HSFI Counters screen under Service Tools. Does the error persist? Replace the MCU Board. Complete.

• Code: 09-608-00 ... 09-611-00
• Description: CMYK Imaging Unit is Near/Past End of Life or Missing The Imaging Unit CRUM indicates the Imaging Unit is near, past end of life, or missing. • 09-608-00 Cyan Imaging Unit is Near End of Life • 09-609-00 Magenta Imaging Unit is Near End of Life • 09-610-00 Yellow Imaging Unit is Near End of Life • 09-611-00 Black Imaging Unit is Near End of Life
• Causes: • Yellow Imaging Unit, PL5.1.8 • Magenta Imaging Unit, PL5.1.9 • Cyan Imaging Unit, PL5.1.10 • Black Imaging Unit, PL5.1.11 • Imaging Unit CRUM, PL5.2.4 • MCU Board, PL10.2.18 • CRUM / Disp Harness, PL11.2.4
• Remedy: • Replace the affected Imaging Unit. • Cycle system power. • If the problem persists, follow the procedure below.
  1 Reseat the indicated Imaging Unit. The error persists. Go to Step 2. Complete. 2 Check connections between P/J12 on the MCU Board and indicated CRUM Connector: P/J208(Y), P/J209 (M), P/J210(C), P/J211 (K). The connection is secure. Go to Step 3. Secure the connection. 3 Check CRUM/Disp Harness continuity between P/J12 on the MCU Board and indicated CRUM Connector: P/J208(Y), P/J209 (M), P/ J210(C), P/J211(K). The harness is undamaged. Go to Step 4. Replace the CRUM/ Dispense Harness. 4 Check for 2.5V at P/J12-3(Y), -7(M), - 11(C), -15(K) on the MCU Board. Is 2.5V available to the indicated Imaging Unit CRUM? Replace the affected Imaging Unit. Replace the MCU Board.

• Code: 09-614-00, 09-631-00
• Description: Fuser Envelope Lever is Up/Down The Envelope Mode Sensor indicates the Fuser’s envelope lever is in the wrong position for the media being fed. • 09-614-00 Fuser Envelope Lever is Up • 09-631-00 Fuser Envelope Lever is Down
• Causes: • Envelop Mode Sensor PL7.2.10 • MCU Board, PL10.2.18 • Exit Harness, PL11.1.7
• Remedy: 1 Remove the Fuser and check the envelope lever and actuator. The lever and actuator are undamaged. Go to Step 2. Replace the Fuser. 2 Test the Envelope Mode Sensor using dc330 (010-206). The signal changes (On/Off). Go to Step 3. Go to Step 4. 3 Check continuity of the Exit Harness between P/J20 on the MCU Board and P/J225 at the sensor. The harness is undamaged. Go to Step 4. Replace the Exit Harness. 4 Check for 3.3V at P/J20-1 on the MCU Board. Is 3.3V available at JJ20-1? Replace the Envelope Mode Sensor. Replace the MCU Board.