Konica-Minolta bizhub 360i
Error Codes List page 2
|
- Code: 14-01, 14-05, 14-40
- Description: When PC-216 is installed
Misfeed at tray 4 paper feed section (When PC-216 is installed)
14-01 After the tray 4 starts to feed paper, the tray 4 vertical transport sensor (PS123) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 4 paper feed sensor (PS122).
14-05 The leading edge of the paper is not turned ON the tray 4 paper feed sensor (PS122) even after the lapse of a given period of time after the tray 4 starts to feed paper. 14-40 For paper fed from the tray 4, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 4 paper feed section results, if the tray 4 vertical transport sensor (PS123) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 4 paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Tray 4 paper feed motor (M121)
• Tray 4 vertical transport motor (M122)
• Tray 4 paper feed sensor (PS122)
• Tray 4 vertical transport sensor (PS123)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS122 I/O check, sensor check PCCB CN18C-2 (ON) PC-216 7-K
3 PS123 I/O check, sensor check PCCB CN18C-5 (ON) PC-216 7-K
4 M121 load check • Check code: 28 • Multi code: 16, 19, 20 PCCB CN9C-1 to 8 PC-216 6-K
5 M122 load check • Check code: 28 • Multi code: 26, 29, 30 PCCB CN9C-9 to 16 PC-216 6-K
6 Replace PCCB.
- Code: 14-01, 14-05, 14-40
- Description: When PC-417 is installed
Misfeed at tray 4 paper feed section (When PC-417 is installed)
14-05 The leading edge of the paper is not turned ON the tray 4 paper feed sensor (PS162) even after the lapse of a given period of time after the tray 4 starts to feed paper.
14-40 For paper fed from the tray 4, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 4 paper feed section results, if the tray 4 paper feed sensor (PS162) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M152)
• Tray 4 paper feed clutch (CL161)
• Tray 4 paper feed sensor (PS162)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS162 I/O check, sensor check PCCB CN4-11 (ON) PC-417 3-C
3 CL161 operation check PCCB CN19-3 (ON) PC-417 6-C
4 M152 load check • Check code: 28 • Multi code: 51, 54, 55 PCCB CN5-1 to 8 PC-417 7-K
5 Replace PCCB.
- Code: 15-01, 15-40
- Description: Misfeed at external LCT paper feed section
15-01 The leading edge of the paper is not turned ON the LU paper feed sensor (PS3) even after the lapse of a given period of time after the external LCT starts to feed paper.
15-40 For paper fed from the external LCT, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the external LCT paper feed section results, if the LU paper feed sensor (PS3) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the external LCT paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • LU paper feed motor (M2)
• LU paper feed sensor (PS3)
• LU drive board (LUDB)
• Base board (BASEB)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 Make the pick-up roller load adjustment of the LCT. - -
3 PS3 I/O check, sensor check LUDB CN5-8 (ON) LU-302 4-G
4 M2 load check • Check code: 28 • Multi code: 41, 44, 45 LUDB CN4-5 to 8 LU-302 3-G
5 Replace LUDB. - -
6 Replace BASEB. - -
7 PCCB F10 or F12 conduction check. (PC-417) - -
8 Replace PCCB. (PC-116/PC-216 / PC-416 / PC-417)
- Code: 16-01, 16-05, 16-40
- Description: Misfeed at transfer LCT paper feed/transport section
16-01 After the transfer LCT starts to feed paper, the vertical transport sensor (PS133) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the paper feed sensor (PS132).
16-05 The leading edge of the paper is not turned ON the paper feed sensor (PS132) even after the lapse of a given period of time after the transfer LCT starts to feed paper.
16-40 For paper fed from the transfer LCT, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the transfer LCT transport section results, if the vertical transport sensor (PS133) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the transfer LCT transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Paper feed motor (M131)
• Vertical transport motor (M132)
• Paper feed sensor (PS132)
• Vertical transport sensor (PS133)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS132 I/O check, sensor check PCCB CN4-11 (ON) PC-416 7-J
3 PS133 I/O check, sensor check PCCB CN4-14 (ON) PC-416 7-J
4 M131 load check • Check code: 28 • Multi code: 1, 4, 5 PCCB CN5-1 to 8 PC-416 5-J
5 M132 load check • Check code: 28 • Multi code: 6, 9, 10 PCCB CN5-9 to 16 PC-416 4-J
6 Replace PCCB.
- Code: 17-30, 17-31
- Description: Tray 3/4 horizontal transport section (When PC-417 is installed)
17-30 The horizontal transport sensor (PS158) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 3 paper feed sensor (PS152).
17-31 The vertical transport sensor (PS153) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the horizontal transport sensor (PS158).
- Paper jam of a sheet of paper left at the tray 3/4 horizontal transport section results, if the horizontal transport sensor (PS158) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 3/4 horizontal transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Intermediate motor (M151)
• Transport motor (M152)
• Tray 3 transport clutch (CL152)
• Horizontal transport clutch (CL153)
• Tray 3 paper feed sensor (PS152)
• Vertical transport sensor (PS153)
• Horizontal transport sensor (PS158)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS152 I/O check, sensor check PCCB CN7-2 (ON) PC-417 5-C
3 PS158 I/O check, sensor check PCCB CN7-5 (ON) PC-417 5-C
4 PS153 I/O check, sensor check PCCB CN4-14 (ON) PC-417 2-C
5 CL152 operation check PCCB CN19-6 (ON) PC-417 6-C
6 CL153 operation check PCCB CN19-8 (ON) PC-417 5-C
7 M151 load check • Check code: 28 • Multi code: 56, 59, 60 PCCB CN20-1 to 3 PC-417 7-K
8 M152 load check • Check code: 28 • Multi code: 51, 54, 55 PCCB CN5-1 to 8 PC-417 7-K
9 PCCB F4 conduction check - -
10 Replace PCCB. - -
- Code: 17-40, 17-41
- Description: Tray 3/4 intermediate transport roller section (When PC-417 is installed)
17-40 The vertical transport sensor (PS153) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 4 paper feed sensor (PS162).
17-41 The tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the vertical transport sensor (PS153).
- Paper jam of a sheet of paper left at the tray 3/4 intermediate transport roller section results, if the tray vertical transport sensor (PS153) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 3/4 intermediate transport roller section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Intermediate motor (M151)
• Transport motor (M152)
• Tray 4 paper feed clutch (CL161)
• Vertical transport sensor (PS153)
• Tray 4 paper feed sensor (PS162)
• Tray 2 vertical transport sensor (PS19)
• PC control board (PCCB)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS153 I/O check, sensor check PCCB CN4-14 (ON) PC-417 2-C
3 PS162 I/O check, sensor check PCCB CN4-11 (ON) PC-417 3-C
4 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K
5 CL161 operation check PCCB CN19-3 (ON) PC-417 6-C
6 M151 load check • Check code: 28 • Multi code: 56, 59, 60 PCCB CN20-1 to 3 PC-417 7-K
7 M152 load check • Check code: 28 • Multi code: 51, 54, 55 PCCB CN5-1 to 8 PC-417 7-K
8 PCCB F4 conduction check - -
9 Replace PCCB. - - 10 Replace BASEB.