Kyocera TaskAlfa 2550ci

Abdul
Posts: 1
Joined: Tue Nov 05, 2019 8:12 pm

Kyocera TaskAlfa 2550ci

Postby Abdul » Tue Nov 05, 2019 8:34 pm

Hi!!!
I’ve having an issue since I changed the printer board.An error code C0180 appears telling to call the service.Can be cleared????
Thank you
ahmed2020
Posts: 1
Joined: Sun Jan 17, 2021 5:02 pm

Re: Kyocera TaskAlfa 2550ci

Postby ahmed2020 » Sun Jan 17, 2021 5:48 pm

:D Eorr 7014
Tadeus
Posts: 25
Joined: Sat Oct 21, 2017 9:43 pm

Re: Kyocera TaskAlfa 2550ci

Postby Tadeus » Tue Feb 02, 2021 11:19 pm

I have some issues with a Kyocera TaskAlfa 2550ci. After changing the printer board, I have a C0180 error.
Any remedy to fix that?
Frank
Posts: 37
Joined: Sat Oct 21, 2017 9:54 pm

Re: Kyocera TaskAlfa 2550ci

Postby Frank » Wed Feb 03, 2021 8:46 am

Kyocera TASKalfa 2550ci is showing error F1D6 what can I do to stop it?
User avatar
Serviceman
Posts: 69
Joined: Sat Oct 21, 2017 9:37 pm

Re: Kyocera TaskAlfa 2550ci

Postby Serviceman » Mon Feb 22, 2021 4:36 pm

Abdul wrote:I’ve having an issue since I changed the printer board. An error code C0180 appears telling to call the service.

Code: 0180
Machine number mismatch
Machine number of main and engine does not match.
Cause:
Data in the EEPROM.
Solution:
Remarks on Main PWB replacement
When replacing the main PWB, remove the EEPROM (YC14) and code DIMM (YS4) from the main PWB that has been removed and then reattach it to the new main PWB.
When refitting DIMM, check "CODE" and "FLS" marked on the PWB and refit them to the original positions.
NOTE: If the code DIMM (YS4) was replaced with a service supplied part, perform the following.
  1. Insert the USB flash device in which the latest firmware was copied, into the slot on the machine and turn
    power on
  2. Referring to the U000 maintenance report printed previously, enter the following values.
    • U252 Setting the destination
    • U265 Setting OEM purchaser code
    • U278 Setting the delivery date
    • U402 Adjusting margins of image printing
    • U952 Maintenance mode workflow
  3. Reset machine settings.( Resets system menu settings modified at setup to their defaults.)
    Main items for settings
    [Date/Timer] - Date/Time settings
    [Date/Timer] - Timer settings (Sleep timer)
    [Edit Destination] - One-touch presetting
    [User/Job accounting] - Defaults for user authentication and job accounting only.
    Resettings are not required as the data are stored in hard disk.
    [FAX] - FAX transmittion settings (tel. no. of itself)
    [System] - Network settings (IP address)
    [Adjustment/Maintenance] - Silent Mode setting
  4. Run the maintenance mode for image adjustments which follows.
    1. Performs maintenance mode U464 (Calibration)
    2. Performs maintenance mode U469 (Auto color registration correction)
    3. Performs maintenance mode U410 (Adjusting the halftone automatically)
NOTE: When connecting the hard disk cables (YC1, YC2) to the PWB, match "BLACK" and "BLUE" marked on the PWB with the connector colors.
NOTE: When connecting the USB cables (YC17, YC21) to the PWB, match "BK" and "WH" marked on the PWB with the connector colors.
User avatar
Serviceman
Posts: 69
Joined: Sat Oct 21, 2017 9:37 pm

Re: Kyocera TaskAlfa 2550ci

Postby Serviceman » Mon Feb 22, 2021 4:42 pm

Frank wrote:Kyocera TASKalfa 2550ci is showing error F1D6 what can I do to stop it?

Code: F1DX
Abnormality detecting of the image memory Management Department
Solution:
  1. Initialize HDD and perform an operation check. (FULL of U024) *
  2. Carry out U021 Main backup initialization and perform an operation check.
  3. Exchange a Main board and perform an operation check.
  4. Exchange HDD and perform an operation check. *
  5. Get USBLOG and contact service headquarters.
* Only HDD standard model

Return to “Kyocera TASKalfa”

Who is online

Users browsing this forum: No registered users and 1 guest