Main |
Sub |
Functions |
Section |
48 |
1 |
Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning direction). |
|
5 |
Used to correction the scan image magnification ratio (in the sub scanning direction). |
Scanner section |
6 |
Used to adjust the rotation speed of each motor. |
|
49 |
1 |
Used to perform the firmware update. |
|
7 |
Used to perform the pre-installed data update. |
|
50 |
1 |
Copy image position, image loss adjustment |
|
5 |
Used to adjust the print lead edge image position. (PRINTER MODE) |
|
6 |
Used to adjust the copy image position and the image loss. (DSPF mode) |
DSPF |
10 |
Used to adjust the black print image magnification ratio and the off-center position. (The adjustment is made separately for each paper feed section.) |
|
12 |
Used to perform the scan image off-center position adjustment. (The adjustment is made separately for each scan mode.) |
|
27 |
Used to perform the image loss adjustment of scanned images in the FAX or image send mode. |
|
28 |
Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio. |
|
51 |
1 |
Used to adjust the ON/OFF timing of the transport voltage. |
|
2 |
Used to adjust the contact pressure (deflection amount) on paper by the main unit and the DSPF registration roller. (This adjustment is performed when there is a considerable variation in the print image position on the paper or when paper jams frequently occur.) |
|
53 |
6 |
Used to adjust the detection level of the DSPF document width. |
|
7 |
Used to adjust the DSPF document size width sensor. |
|
8 |
Used to adjust the document lead edge reference and the DSPF mode document scan position. |
|
9 |
DSPF dirt detection setting. |
|
10 |
DSPF dirt detection execution. |
|
55 |
1 |
Used to set the specifications of the engine control operations. (SOFT SW) |
|
2 |
Used to set the specifications of the scanner control operation. (SOFT SW) |
|
3 |
Used to set the specifications of the controller operation. (SOFT SW) |
|
10 |
Used to set the special stamp text. (Taiwan only) |
|
56 |
1 |
Used to transport data between Storage - MFP PWB SRAM/EEPROM. (Used to repair the PWB.) |
|
2 |
Used to backup the data in the EEPROM and Storage to the USB memory. |
|
3 |
Used to backup the document filing data to the USB memory. |
|
4 |
Used to backup the JOB log data to the USB memory. |
|
5 |
Used to import the SIM22-6 data to a USB memory in the TEXT format. |
|
6 |
Used to output the JAM/trouble data. |
|
7 |
Used to backup the SYS log data to the USB memory. |
|
15 |
Used to restore the data of MFP EEPROM. |
|
99 |
Used to backup all log data. |
|
60 |
1 |
Used to check the memory operations (read/write) of the MFP PWB. |
|
61 |
1 |
Used to check the LSU polygon motor rotation and laser detection. |
LSU |
3 |
Used to set the laser power |
|
11 |
Used to correct the laser power automatically. |
|
12 |
Laser power manual correction |
LSU |
13 |
Used to clear the laser power correction value. |
|
14 |
Used to set the laser power correction. |
|
62 |
1 |
Used to format the Storage. (HDD: Excluding the Operation manual and the watermark data) |
|
3 |
Used to check read/write of the Storage. (all areas). |
|
4 |
Used to check each partition and do theoretical format. |
|
7 |
Used to print the Storage. self diagnostics error log. |
|
9 |
Used to delete the storage data. |
|
12 |
Used to set the automatic format at storage trouble. |
|
14 |
Used to delete the document filing management data. |
HDD |
21 |
Used to display the information on the MFP storage. |
|