Sharp MXM2630
Simulation mode. List of classic mode 41 - 50
| Sim No. | Function | Easy Mode | |||
| Installation | Maintenance | Adjustment and Settings |
|||
| 41 | 2 | Set the document size sensor detection level | 3 | ||
| 3 | Check the operation of the document size sensor and control circuit | ||||
| 43 | 1 | Set the fusing temperature in each mode | |||
| 2 | Set the fusing operation and preheat mode | ||||
| 20 | Set the fusing temperature in each mode (environment correction under low temperature and low humidity of Sim43- 2) | ||||
| 21 | Set the fusing temperature in each mode (environment correction under high temperature and high humidity of Sim43- 2) | ||||
| 24 | Set the fusing operation | ||||
| 35 | Check fusing belt pressure state | ||||
| 44 | 1 | Set each correction operation function in the image forming section | |||
| 2 | Set the sensitivity of the image density sensor |
2-2 2-3 |
2 | ||
| 4 | Set the condition of the high density process control operation | ||||
| 6 | Execute the high density process control forcibly | 1-5 | 2-3 | ||
| 9 | Check the high density process control operation data | ||||
| 12 | Check the high density process control and the image density sensor operation data | ||||
| 14 | Check the output level of the temperature and humidity sensor | ||||
| 15 | Set the OPC drum idle rotation | ||||
| 17 | Execute refresh operation of the developer and transfer roller | ||||
| 21 | Set the halftone process control target | 5 | |||
| 22 | Check the toner patch density level in the halftone process control operation | ||||
| 24 | Check the correction target and the correction level in the halftone process control operation | ||||
| 25 | Set the calculating conditions of the correction value for the halftone process control | ||||
| 26 | Execute the halftone process control forcibly | 1-5 | 2-3 | ||
| 27 | Clear the correction data of the halftone process control | ||||
| 28 | Set the process control execution condition | ||||
| 29 | Set the operating condition of the halftone process control | ||||
| 37 | Set the developer bias correction level in the continuous printing operation | ||||
| 43 | Check the identification information of the developing unit | ||||
| 62 | Set the process control execution condition | ||||
| 46 | 2 | Adjust the copy density in the copy mode | |||
| 4 | Adjust the color scan density in the image send mode | ||||
| 5 | Adjust the monochrome scan density in the image send mode | ||||
| 8 | Adjust the color balance RGB in the image send mode | ||||
| 9 | Adjust the scan image density (SPF) | 3 | |||
| 10 | Adjust the copy gray balance and gamma (for each copy mode) | ||||
| 46 | 16 | Adjust the copy gray balance and gamma (for all mode) | 1-3 | 5 | |
| 19 | Set the scanning operating condition of the document density in the auto mode | ||||
| 23 | Set the density correction of copy high density area (for high density tone gap) | ||||
| 24 | Adjust copy gray balance (auto adjustment) | 5 | |||
| 32 | Adjust the document background density reproducibility in the auto mode | ||||
| 37 | Adjust the reproducibility capability of gray image creation | ||||
| 39 | Adjust the sharpness of send image | ||||
| 40 | Adjust the FAX send image density (all modes) | ||||
| 41 | Adjust the FAX send image density (normal) | ||||
| 42 | Adjust the FAX send image density (fine) | ||||
| 43 | Adjust the FAX send image density (super fine) | ||||
| 44 | Adjust the FAX send image density (ultra fine) | ||||
| 45 | Adjust the FAX send image density (600dpi) | ||||
| 46 | Adjust the FAX send image density (RGB RIP) | ||||
| 47 | Set the compression ratio of copy and scan images (JPEG) | ||||
| 48 | Set the copy output resolution in the copy mode | ||||
| 51 | Adjust the gamma of heavy paper mode and image process mode in the copy mode | ||||
| 52 | Set gamma default value of heavy paper mode and image process mode in the copy mode | 1-3 | |||
| 54 | Adjust the engine halftone auto density (dither) | 1-3 | |||
| 55 | Adjust the dropout color in the image send mode | ||||
| 58 | Set pseudo resolution in the copy mode | ||||
| 60 | Set the sharpness in auto mode | ||||
| 61 | Set the area separation recognition level | ||||
| 62 | Set the operating condition of the auto color selection, the area separation, the background image process and the auto exposure mode | ||||
| 63 | Adjust the density in the copy low density | ||||
| area | |||||
| 66 | Adjust the reproduction capability of watermark in the copy/printer mode | ||||
| 74 | Adjust copy gray balance (auto) / printer | 1-1 | 2-2 | 1-2 | |
| gray balance (auto) | 1-5 | 2-3 | 1-3 2 |
||
| 90 | Set the process operation of high compression PDF image | ||||
| 91 | Adjust the reproduction capability of black text | ||||
| 48 | 1 | Adjust the scan image magnification ratio (main scanning direction and sub scanning direction) | 1-1 | ||
| 5 | Adjust the scan image magnification ratio (sub scanning direction) | 1-1 | |||
| 6 | Adjust the rotation speed of each motor | ||||
| 49 | 1 | Update the firmware | 4 | 5 | |
| 7 | Update the preinstalled firmware | 4 | 5 | ||
| 50 | 1 | Adjust the copy image position and the image loss | 1-1 | ||