Sharp MXM160
Simulation mode. List of simulation codes 25 - 67
| Main code | Sub code | Contents |
|---|---|---|
| 25 | 02 | Toner density reference control level setting (automatic development adjustment) |
| 10 | Polygon motor operation check | |
| 26 | 01 | Job separator setting |
| 02 | Size setting | |
| 03 | Auditor setting | |
| 04 | Copier duplex setting | |
| 05 | Count mode setting | |
| 06 | Destination setting | |
| 07 | Machine condition check | |
| 18 | Toner save mode setting | |
| 20 | Job separator paper exit mode setting | |
| 22 | Language setting clear | |
| 30 | CE mark conformity control ON/OFF | |
| 31 | Auditor mode exclusive setup | |
| 36 | Cancel of stop at maintenance life over | |
| 37 | Cancel of stop at developer life over | |
| 38 | Cancel of stop at drum life over | |
| 39 | Memory capacity check | |
| 42 | Transfer ON/OFF timing control setting | |
| 43 | Side void amount setting | |
| 51 | Copy temporary stop function setting | |
| 54 | LCD contrast PWM duty setting | |
| 56 | Life correction ON/OFF setting | |
| 60 | [FAX] key Enable/Disable setting | |
| 73 | Toner save setting display/non-display | |
| 74 | Total counter display change setting | |
| 30 | 01 | Paper sensor status display |
| 41 | 01 | Document size detection photo sensor check |
| 02 | Document size detection photo sensor detection level adjustment | |
| 03 | Document size detection photo sensor light receiving/ detection level check | |
| 04 | Detection level adjustment when the document size is settled(15degrees - 20degrees) | |
| 42 | 01 | Developing counter clear |
| 43 | 01 | Fusing temperature setting (Normal copy) |
| 12 | Standby mode fusing fan rotation setting | |
| 13 | Paper interval control allow/inhibit setting | |
| 44 | 01 | Enable/Disable setting of toner density control correction |
| 16 | Toner density control data check and toner density correction quantity display | |
| 34 | Transfer current setting | |
| 46 | 01 | Copy density adjustment (300dpi) |
| 02 | Copy density adjustment (600dpi) | |
| 09 | Copy exposure level adjustment, individual setting (Text) 300dpi | |
| 10 | Copy exposure level adjustment, individual setting (Text) 600dpi | |
| 11 | Copy exposure level adjustment, individual setting (Photo) 600dpi | |
| 18 | Image contrast adjustment (300dpi) | |
| 19 | Exposure mode setting (Gamma table setting/AE operation mode setting/ Photo image process setting) |
|
| 20 | SPF/RSPF exposure correction *2 | |
| 29 | Image contrast adjustment (600dpi) | |
| 30 | AE limit setting | |
| 46 | 31 | Image sharpness adjustment |
| 48 | 01 | Main/sub scanning magnification ratio adjustment |
| 05 | SPF/RSPF mode sub scanning magnification ratio adjustment in copying *2 | |
| 49 | 01 | Flash ROM program writing mode |
| 50 | 01 | Image lead edge adjustment |
| 06 | Copy lead edge position adjustment (SPF/RSPF) *2 | |
| 10 | Paper off-center adjustment | |
| 12 | Document off-center adjustment | |
| 18 | Memory reverse position adjustment in duplex copy *1 | |
| 19 | Rear edge void adjustment in duplex copy *6 | |
| 51 | 02 | Resist amount adjustment |
| 53 | 08 | SPF/RSPF scanning position automatic adjustment *2 |
| 10 | SPF/RSPF scanning position setting | |
| 61 | 02 | Laser power correction ON/OFF |
| 03 | HSYNC output check | |
| 63 | 01 | Shading check |
| 07 | SPF/RSPF automatic correction *2 | |
| 64 | 01 | Self print |
| 65 | 10 | Key reception time setting display/non-display setting |
| 11 | Info lamp setting | |
| 67 | 50 | USB reception speed adjustment |
<Execution inhibit conditions>
*1)Execution is inhibited when the duplex setup is OFF and other than RSPF is set.
*2)Execution is inhibited when OC.
*3)Execution is inhibited when SPF. (Not RSPF)
*4)Execution is inhibited when the job separator is not installed.
*5)Execution is inhibited when the model is not provided with the CRUM.
*6)Execution is inhibited when the duplex setup is OFF.