Main |
Sub |
Function (Purpose) |
Section |
Purpose |
62 |
1 |
Used to format the hard disk. (Except for the operation manual area.) |
|
|
2 |
Used to check the read/write operation of the hard disk. (Partial section) |
|
Operation test/check |
3 |
Used to check the read/write operation of the hard disk. (All area) |
|
Operation test/check |
6 |
Used to perform the self diag of the hard disk. |
|
Operation test/check |
7 |
Used to print the self diag error log of the hard disk. |
|
Operation test/check |
8 |
Used to format the hard disk. (Except for the system area and the operation manual area.) |
|
|
10 |
Used to delete the job log data. |
|
Data clear |
11 |
Used to delete the document filing data. |
|
Data clear |
12 |
Used to set YES/NO of auto format in hard disk trouble. |
|
Setting |
13 |
Used to format the hard disk.(Operation manual area only). |
|
|
14 |
Used to delete the document filing management data. |
HDD |
Data clear |
20 |
Used to check the operation of the mirroring hard disk. |
Mirroring hard disk |
Operation test/check |
63 |
1 |
Used to check the result of the shading correction. |
|
Operation data check |
2 |
Used to execute shading forcibly. |
Scanner |
Adjustment |
3 |
Used to perform the gamma correction and density conversion for RGB data inputted from the CCD. The gamma correction 1 of the SCAN ASIC and the set value of color correction are calculated and set from the specified image data. |
Scanner |
Adjustment |
4 |
The average value of the patch scan values for the RGB image data inputted from the CCD are calculated and displayed. |
Scanner |
|
5 |
Used to reset the color balance of the scanner to the default. |
|
Adjustment/Setting |
6 |
Used to set the auto adjustment pattern of the engine and gray balance. |
|
Adjustment/Setting |
7 |
Used to set the auto density of the engine auto adjustment scanner target value. (Service) |
|
Adjustment/Setting |
8 |
Used to reset the engine auto adjustment scanner target value to the default value. |
|
Adjustment/Setting |
64 |
2 |
Self print (B/W mode) |
|
Operation test /check |
3 |
Self print (B/W mode: high speed process) |
|
Operation test/check |
4 |
Used to make the self print of the printer. |
|
Operation test/check |
5 |
Printer self print (PCL) When supporting the FIERY option, Sim is not displayed. |
|
Operation test/check |
6 |
Printer self print (PS) For FIERY option support, Sim is not displayed. |
|
Operation test/check |
7 |
Used to print the adjustment pattern of the test print. (Self print). (The adjustment pattern of SIM46-16 is printed.) |
|
Operation test/check |
65 |
1 |
Used to adjust the touch panel (LCD display section) detection coordinates. |
Operation panel section |
Adjustment |
2 |
Used to display the touch panel (LCD display section) detection coordinates. |
|
Operation check/Test |
5 |
Used to check the operation panel key input. |
|
Operation check/Test |
66 |
1 |
Used to change and check the soft switch setting. |
|
Setting |
2 |
Used to clear the soft switch and set the default value. |
FAX |
Data clear |
10 |
Used to clear all the data (memory receive and send) of the image memory.* The confidential receive data are cleared simultaneously. |
FAX |
Data clear |
29 |
Used to clear the data related to the address book (one-touch registration, FTP/Desktop extension, group extension, program registration, interface memory box, meta data, Inbound Routing, Document Admin table). |
|
Data clear |
67 |
17 |
Printer reset |
Printer |
Reset |
24 |
Used to set for auto gray calibration. For FIERY option support, Sim is not displayed. |
|
Adjustment/Setting |
25 |
Used to set the printer engine gray balance manual correction. For FIERY option support, the Sim is not displayed. |
|
Adjustment/Setting |
27 |
Used to register the scanner target value of the printer engine auto density adjustment. For FIERY option support, this Sim is not displayed. |
|
Adjustment/Setting |
28 |
Used to reset the printer engine auto adjustment scanner target value to the default value. For FIERY option support, Sim is not displayed. |
|
Adjustment/Setting |
31 |
Used to clear the printer calibration value. For FIERY option support, the Sim is not displayed. |
|
Data clear |
32 |
Printer screen gamma table setting (300/600DPI). When supporting the FIERY option, Sim is not displayed. |
|
Adjustment/Setting |
33 |
Used to perform the gamma correction of printer screens (for PCL). For FIERY option support, the Sim is not displayed. |
|
Adjustment/Setting |
34 |
Used to set Enable/Disable of the printer half-tone max. density correction. For FIERY option support, Sim is not displayed. |
|
Adjustment/Setting |
36 |
Used to adjust the density in the low density section. For FIERY option support, Sim is not displayed. |
Printer |
Adjustment/Setup |
45 |
Used to adjust the printer image filter and trapping. |
|
Adjustment/Setup |
52 |
Used to set the default of the gamma of the printer screen. For FIERY option support, Sim is not displayed. |
Printer |
Adjustment/Setup |
54 |
Printer color balance adjustment (Automatic adjustment for each dither) For FIERY option support, Sim is not displayed. |
Printer |
Adjustment |