| Main |
Sub |
Function (Purpose) |
Section |
Purpose |
| 48 |
1 |
Used to adjust the copy magnification ratio (main/sub scanning direction). |
|
Adjustment |
| 5 |
Used to adjust the copy magnification ratio (sub scanning direction).This adjustment is performed when Sim. 48-1 is used to adjust the sub scanning direction magnification ratio and a copy is made in a different copy magnification ratio and a satisfactory result is not obtained. |
Scanner section |
Adjustment |
| 6 |
Used to adjust the rotation speed of each motor. |
|
Adjustment |
| 49 |
1 |
Firmware update |
|
|
| 3 |
Used to update the instruction manual stored in the HDD. |
|
|
| 5 |
Used to perform the watermark update. |
|
|
| 10 |
Used to perform ACU update. |
|
|
| 50 |
1 |
Used to adjust copy image position on print paper and the void area (image loss) in the copy mode. (The similar adjustment can be performed with Sim. 50-5 and Sim. 50-2 (Simple method). (Document table mode)) |
|
Adjustment |
| 2 |
Used to adjust the copy image position on the paper and the void area (image loss) in the copy mode. (This simulation, similar to Sim. 50-1, provides more simplified adjustment.) |
|
Adjustment |
| 5 |
Used to adjust the printer print lead edge. |
|
Adjustment |
| 6 |
DSPF document lead edge adjustment. Used to adjust the copy image position on print paper and the void area (image loss) in the copy mode. (The similar adjustment can be performed with Sim. 50-7 (Simple method).) (DSPF mode) |
DSPF |
Adjustment |
| 7 |
DSPF document lead edge adjustment (Simple method) Used to adjust the copy image position on print paper and the void area (image loss)in the copy mode (Sim. 50-6 simple method) |
DSPF |
Adjustment |
| 10 |
Used to adjust the print image off-center position. (The adjustment is made for each paper feed section.) |
|
Adjustment |
| 12 |
Used to adjust the scan image off-center position. (The adjustment is made for each scan mode.) |
|
Adjustment |
| 27 |
Used to adjust the image loss of a scan image in the FAX/Scanner mode. |
|
Adjustment |
| 28 |
Used to perform the OC adjustment, the BK main scan magnification ratio correction, the DSPF adjustment, and the print position adjustment. |
|
Adjustment |
| 51 |
1 |
Used to adjust the ON/OFF timing of the secondary transport voltage. |
|
Adjustment/Setting |
| 2 |
Used to adjust the contact pressure of paper against the resist roller (main unit paper feed, duplex paper feed, DSPF paper feed) in each section. (This adjustment is required when there is a great variation in the print image position for the paper or when paper jam occurred.) |
|
Adjustment/Setting |
| 53 |
6 |
Used to adjust the DSPF width detection level. |
|
Adjustment |
| 7 |
Used to set the DSPF width adjustment value. (Sim. 53-6 manual input) |
|
Adjustment/Setting |
| 8 |
Used to adjust the DSPF document scan start position. |
|
Adjustment |
| 9 |
DSPF dirt detection setting |
|
Adjustment/Setup |
| 10 |
DSPF dirt detection execution. |
|
|
| 12 |
Used to check the operations of the DSPF double feed sensor. |
|
Adjustment |
| 55 |
1 |
Used to set the specifications of the engine control operation. |
|
(Must not be used unless a special change is required.) |
| 2 |
Used to set the specifications of the controller operation. |
|
(Must not be used unless a special change is required.) |
| 3 |
Used to set the specifications of the controller operation. |
|
(Must not be used unless a special change is required.) |
| 10 |
Used to enter the special stamp text input. |
|
Special stamp text setting |
| 56 |
1 |
Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.) |
|
Backup |
| 2 |
Used to backup the data in the EEPROM. SD Card, and HDD (including user authentication data and address data) to the USB memory. (Corresponding to the device cloning and the storage backup.) |
|
Data backup |
| 3 |
Used to back up the document filing data. |
|
Backup |
| 4 |
Used to back up the job log data. |
|
Backup |
| 5 |
Used to import the SIM22-6 data to a USB memory in the TEXT format. |
|
Adjustment/Setting/ Operation data check |
| 6 |
Used to output the JAM/trouble data. |
|
|
| 7 |
Used to backup the system log. |
|
|
| 99 |
Used to export sys log data to the USB memory. |
|
|
| 60 |
1 |
Used to check the operations (read/write) of the MFP control (SDRAM). |
|
Operation test/check |
| 61 |
1 |
Used to check the polygon motor rotation and the BD signal detection. |
|
Adjustment/Setting |
| 2 |
Used to set the laser power. |
|
Adjustment/Setup |
| 3 |
Used to set the laser power. |
|
Adjustment/Setting |
| 4 |
Used to print the print image skew adjustment pattern. (LSU unit) |
|
Adjustment |
| 11 |
Used to correct the laser power automatically. |
|
Adjustment |
| 12 |
Laser power manual correction |
LSU |
Adjustment |
| 13 |
Used to clear the laser power correction value. |
|
Adjustment |