Main |
Sub |
Function (Purpose) |
Section |
Purpose |
44 |
1 |
Used to set each correction function of the image forming (process) section. |
Process (OPC drum, developing, transfer, cleaning) |
Setting |
2 |
Used to adjust the process control sensor gain. |
Process |
Adjustment/Setting |
3 |
A change in the OPC drum surface potential VO due to the OPC drum environment and membrane decrease (life) is detected with the surface potential sensor to correct the grid potential Vg so that the cleaning field is maintained at a constant level. |
Process |
Operation test/check |
4 |
Used to set the operating conditions of the high density process control. |
|
(Must not be used unless a special change is required.) |
5 |
Used to set the dark potential adjustment conditions. |
|
Adjustment/Setting |
6 |
Used to perform forcible execution of the high density process correction. |
|
Adjustment |
9 |
Used to display the process data. |
Process (OPC drum, developing, transfer, cleaning) |
(This simulation is normally not used in the market.) |
12 |
Used to display the result of the high density process control. |
Process (OPC drum, development) |
(This simulation is normally not used in the market.) |
14 |
Used to check the output levels of the fusing temperature sensor, the machine temperature sensor, and the humidity sensor. |
Process (OPC drum, development) |
Adjustment/Setting/ Operation data check |
15 |
Used to set the OPC drum idle rotation. |
Process |
Setting |
21 |
Used to set the halftone process control target. |
Process |
Adjustment/Setup |
22 |
Used to display the toner patch density level in the halftone process control operation. |
Process |
Operation data display |
24 |
Used to display the correction target and the correction level in the halftone process control operation. |
Process |
Operation data display |
25 |
Used to set the calculating conditions of the correction value for the halftone process control. |
Process |
Setting |
26 |
Used to execute the halftone process control compulsory. |
Process |
Adjustment/Setup |
27 |
Used to clear the correction data of the halftone process control. |
Process |
Data clear |
28 |
Used to set the process control execution timing. |
|
Adjustment/Setting |
29 |
Used to set the operating conditions of the process control during a job. |
Process |
Setting |
33 |
Used to set the conditions of the half-tone potential adjustment. |
|
Adjustment/Setting |
35 |
Used to display the half-tone potential adjustment result. |
|
|
37 |
Used to set the development bias correction level in the continuous printing operation. |
|
Adjustment/Setup |
62 |
Used to set the process control execution conditions. |
Process |
Setup/Adjustment |
46 |
2 |
Used to adjust the copy density in the copy mode. |
|
Adjustment (Monochrome copy mode) |
4 |
Used to adjust the density in the image send mode. |
|
Adjustment (Color scanner mode) |
5 |
Used to adjust the density in the image send mode. |
|
Adjustment (Monochrome scanner mode) |
8 |
Used to adjust the scanner color balance RGB. |
|
Adjustment (Color scanner mode) |
9 |
Used to adjust the copy density adjustment in the copy mode. |
|
Adjust (DSPF mode) |
10 |
Used to perform the engine gray balance manual adjustment. |
|
Adjustment |
16 |
Used to perform the engine balance manual adjustment. (Monochrome, all modes) |
|
Adjustment |
19 |
Used to set the monochrome auto exposure mode. |
|
Setting |
23 |
Used to set the half-tone max. density correction. |
|
Adjustment/Setting |
24 |
Used to adjust the engine half-tone auto density adjustment. |
|
Adjustment |
32 |
Adjustment of basic color density for AE mode. |
|
Adjustment/Setting |
37 |
Used to adjust B/W image forming. |
|
Adjustment/Setting |
47 |
Used to set the JPEG compression rate in copying and scanning. |
|
Adjustment/Setting |
48 |
Copy output resolution setting |
|
Adjustment/Setting |
51 |
Used to adjust the gamma for the copy mode heavy paper mode and the image process mode. |
|
Adjustment/Setup |
52 |
Used to set the gamma default for the copy mode heavy paper and the image process mode. (After execution of either SIM46-54 or SIM46-51, the adjustment value is reset to the initial value.) |
|
Adjustment/Setup |
54 |
Used to perform the engine halftone automatic density adjustment (dither). |
|
Adjustment |
55 |
Used to adjust the drop out color in the image send mode (monochrome manual text mode). |
|
Adjustment/Setup |
60 |
Used to adjust the sharpness in the color auto mode. |
|
Adjustment/Setup |
61 |
Used to adjust the area separation recognition level. |
|
Adjustment/Setup |
62 |
Used to set the operating conditions of the ACS, the area separation, the background image process, and the auto exposure mode. |
|
Adjustment/Setup |
63 |
Used to adjust the density in the copy low density section. |
|
Adjustment/Setup |
66 |
Used to adjust the reproduction capability of watermarks in the copy/printer mode. |
|
Adjustment/Setup |
74 |
Copy gray balance adjustment (Auto adjustment)/Printer gray balance adjustment (Auto adjustment) |
|
Adjustment |
90 |
Used to set the process operation of high-compression PDF images. |
|
Adjustment |
91 |
Used to adjust the reproduction capability of black text. |
|
Adjustment |