Sharp MXC305W
Simulation mode. List of classic mode. Codes 27-9 - 46-47
Sim No. | Content | Installation | Maintenance | Adjustment and Settings |
---|---|---|---|---|
27-9 | Used to set the paper transport time recording Yes/No threshold value and shading gain adjustment retry number | 2-5 | ||
27-10 | Used to clear the trouble prediction history information | |||
27-11 | Used to check the serial communication retry number and the scanner gain adjustment retry number history | |||
27-12 | Used to check the high density, halftone process control and the automatic registration adjustment error history | |||
27-13 | Used to check the history of paper transport time between sensors | |||
27-14 | Used to set the FSS function connection test mode |
2-5 | ||
27-15 | Used to display the FSS connection status | 2-5 | ||
27-16 | Used to set the FSS alert send | 2-5 | ||
30-1 | Used to check the operations of the sensors and the detectors in other than the paper feed section and the control circuit | |||
30-2 | Used to check the operations of the sensors and the detectors in the paper feed section and the control circuit | |||
43-1 | Used to set the fusing temperature in each mode | |||
43-2 | Used to set the fusing operation and preheating | |||
43-20 | Used to set the environment correction under low temperature and low humidity (L/ L) for the fusing temperature setting (Sim43- 2) in each paper mode |
|||
43-21 | Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (Sim43-2) in each paper mode | |||
43-24 | Fusing motion setup | |||
43-35 | Fusing nip operation check | |||
44-1 | Used to set each correction operation function in the image forming section | |||
44-2 | Used to adjust the sensitivity of the image | 2-2 | 2 | |
density sensor | -3 | |||
44-4 | Used to set the conditions of the high density process control operation | |||
44-6 | Used to execute the high density process control forcibly | 1-5 | 2-3 | |
44-9 | Used to display the result data of the high density process control operation | |||
44-12 | Used to display the operation data of the high density process control and the image density sensor | |||
44-14 | Used to display the output level of the temperature and humidity sensor | |||
44-15 | Used to set the OPC drum idle rotation | |||
44-21 | Used to set the halftone process control target | 5 | ||
44-22 | Used to display the toner patch density level in the halftone process control operation | |||
44-24 | Used to display the correction target and the correction level in the halftone process control operation | |||
44-25 | Used to set the calculating conditions of the correction value for the halftone process control | |||
44-26 | Used to execute the halftone process control compulsory | 1-5 | 2-3 | |
44-27 | Used to clear the correction data of the halftone process control | |||
44-28 | Used to set the process control execution conditions | |||
44-29 | Used to set the operating conditions of the process control during a job | |||
44-37 | Used to set the development bias correction level in the continuous printing operation | |||
44-43 | Used to display the identification information of the developing unit | |||
44-62 | Used to set the process control execution conditions | |||
46-1 | Used to adjust the copy density in the copy mode | |||
46-2 | Used to adjust the copy density in the copy mode | |||
46-4 | Used to adjust the density in the image send mode | |||
46-5 | Used to adjust the density in the image send mode | |||
46-8 | Used to adjust the image send mode color balance RGB | |||
46-9 | Used to adjust the scan image density | 3 | ||
46-10 | Used to adjust the copy color balance and the gamma (for each color copy mode) | |||
46-16 | Used to adjust the monochrome copy density and the gamma | |||
46-19 | Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode documents | |||
46-21 | Copy color balance adjustment (manual adjustment) | 1-3 | 5 | |
46-23 | Used to set the density correction of copy high density section (high density tone gap supported) | |||
46-24 | Copy color balance adjustment (auto adjustment) | 5 | ||
46-25 | Used to adjust the copy color balance (single color copy mode) | |||
46-26 | Used to reset the single color mode color balance set value to the default | |||
46-27 | Used to adjust the gamma/density of copy images, text and line image edges | |||
46-30 | Used to adjust the resolution in the sub scanning direction in the copy mode | |||
46-32 | Used to adjust the document background density reproducibility in the monochrome auto copy mode | |||
46-36 | Used to adjust the colors in the two color copy mode | |||
46-37 | Used to adjust the reproduction capability of monochrome mode color | |||
46-38 | Used to adjust the black component amount in the color copy mode | |||
46-39 | Used to adjust the sharpness of FAX send images | |||
46-40 | Used to adjust the FAX send image density (Collective adjustment of all the modes) | |||
46-41 | Used to adjust the FAX send image density (Normal) | |||
46-42 | Used to adjust the FAX send image density (Fine) | |||
46-43 | Used to adjust the FAX send image density (Super fine) | |||
46-44 | Used to adjust the FAX send image density (Ultra fine) | |||
46-45 | Used to adjust the FAX send image density (600dpi) | |||
46-46 | Used to adjust the FAX send image density (RGB RIP) | |||
46-47 | Used to set the compression rate of copy and scan images (JPEG) |