Sharp MXC301
Simulation mode. List of simulation code 46 - 67
Main | Sub | Functions | Section |
---|---|---|---|
46 | 1 | Used to adjust the copy density in the color copy mode. | |
2 | Used to adjust the copy density in the monochrome copy mode. | ||
4 | Used to adjust the density in the color image send mode. | ||
5 | Used to adjust the density in the monochrome image send mode. | ||
9 | Used to adjust the scan image density. | ||
19 | Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode documents. | ||
21 | Copy color balance adjustment (Manual adjustment) | ||
23 | Used to set the density correction of copy high density section (High density tone gap supported). | ||
24 | Color balance adjustment (Auto adjustment) | ||
27 | Used to adjust the gamma/density of copy images, texts, and line image edges. | ||
32 | Used to set the AE reactivity control. | ||
37 | Used to adjust the color document reproducibility in the monochrome copy mode. | ||
39 | Used to adjust the sharpness of FAX send images. | ||
40 | Used to adjust the FAX send image density. (Collective adjustment of all the modes) | ||
41 | Used to adjust the FAX send image density. (Normal) | ||
42 | Used to adjust the FAX send image density. (Fine) | ||
43 | Used to adjust the FAX send image density. (Super Fine) | ||
51 | Used to adjust the gamma for the copy mode heavy paper mode and the image process mode. (Manual adjustment) |
||
52 | Used to reset the copy color balance adjustment (adjustment for each dither) to the default value. (The set values of SIM46-51 and SIM46-54 are set to the default values.) |
||
54 | Used to reset the copy color balance adjustment (auto adjustment for each dither). | ||
48 | 1 | Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning direcĀtion). | |
6 | Used to adjust the rotation speed of each motor. | ||
49 | 1 | Used to perform the firmware update. | |
2 | Used to perform the FPGA update. | ||
50 | 1 | Copy image position, image loss adjustment | |
5 | Used to adjust the print lead edge image position. (PRINTER MODE) | ||
6 | Used to adjust the copy image position and the image loss. (RSPF mode) | RSPF | |
10 | Used to adjust the black print image magnification ratio and the off-center position. (The adjustment is made separately for each paper feed section.) |
||
12 | Used to perform the scan image off-center position adjustment. (The adjustment is made separately for each scan mode.) |
||
20 | Image registration adjustment (Manual adjustment) | ||
22 | Used to adjust the image registration. (Main scan direction, sub scan direction) (Auto adjustment)/OPC drum phase adjustment (Auto adjustment) |
||
51 | 1 | Used to adjust the ON/OFF timing of the secondary transport voltage. | |
2 | Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF resist roller. (This adjustment is performed when there is a considerable variation in the print image position on the paper or when paper jams frequently occur.) | ||
53 | 8 | Used to adjust the document lead edge reference and the SPF mode document scan position. | |
9 | Used to detect the dirt of the SPF | ||
10 | Used to set the display of the dirt detection position of the SPF | ||
55 | 1 | Used to set the specifications of the engine control operations. (SOFT SW) | |
2 | Used to set the specifications of the scanner control operation. (SOFT SW) | ||
3 | Used to set the specifications of the controller operation. (SOFT SW) | ||
56 | 2 | Used to backup the data in the EEPROM and Flash memory (including user authentication data) to the USB memory. (Corresponding to the device cloning and the storage backup.) | |
5 | Used to print out the each data and simulation list | ||
60 | 1 | Used to check the operations (read/write) of the MFP PWB memory. | |
61 | 1 | Used to check the LSU polygon motor rotation and laser detection. | LSU |
3 | Used to set the laser power | ||
4 | Used to print the print image skew adjustment pattern. (LSU unit) | ||
63 | 1 | Used to display the shading correction result. | Scanner |
2 | Used to perform shading. | ||
3 | Used to perform scanner (CIS) color balance and gamma auto adjustment. | Scanner | |
5 | Used to perform the scanner (CIS) color balance and gamma default setting. | ||
12 | Used to set the target color balance of the copy mode auto color balance adjustment. | ||
64 | 1 | Test print. (Self print) (Color mode) | |
2 | Test print. (Self print) (Monochrome mode) | ||
4 | Printer test print. (Self print) | ||
5 | Printer test print. (Self print) (PCL) | ||
6 | Printer test print. (Self print) (PS) | ||
65 | 10 | Used to set the display of key standby time. | |
66 | 1 | Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while checking with the LCD. | FAX |
2 | Used to enter a country code and set the default value for the country code. | FAX | |
4 | Used to send the selected signals to the line and the main unit speaker. | FAX | |
7 | Used to output all image data saved in the image memory of FAX part. | FAX | |
8 | Used to send the selected sound messages to the line and the speaker. | FAX | |
10 | Used to clear the FAX image data. | FAX | |
11 | Used to send the selected signal at 300bps to the line and the speaker. | FAX | |
13 | Used to execute the dial send test. | FAX | |
17 | Used to send the DTMF signal to the line and the speaker. | FAX | |
21 | Used to print the selected items (FAX setting list, software SW list, protocol monitor). | FAX | |
30 | Used to display the TEL/LIU status change, The display is highlighted by status change. | FAX | |
31 | Used to set ON/OFF the port for output to TEL/LIU. | FAX | |
32 | Used to check the fixed data received from the line and to display the result. | FAX | |
33 | Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected, the display is highlighted. | FAX | |
34 | Used to execute the send test and display the time for sending (receiving) the image data during sending the test data on LCD. | FAX | |
67 | 25 | Printer color balance adjustment (Manual adjustment) | Printer |
31 | Used to clear the calibration value. | Printer | |
33 | Used to change the gamma of the printer screen. | Printer | |
34 | Used to set the density correction in the printer high density section. (Support for the high density section tone gap) | Printer | |
36 | Used to adjust the density in the low density section. | Printer | |
52 | Used to reset the printer color balance adjustment (adjustment for each dither) to the default value. (The set values of SIM67-33 are set to the default values.) |