Main |
Sub |
Functions |
Section |
26 |
6 |
Used to set the specifications (paper, fixed magnification ratio, etc.) of the destination. |
|
18 |
Used to set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.) |
|
30 |
Used to set the operation mode corresponding to the CE mark (Europe safety standards). (For slow start to drive the fusing heater lamp) |
|
35 |
Used to set the display mode of SIM 22-4 trouble history when a same trouble occurred repeatedly. There are two display modes: display as one trouble and display as several series of troubles. |
|
38 |
Used to set Continue/Stop of print when the maintenance life is reached. |
|
53 |
User auto color calibration (color balance adjustment) Inhibit/Allow setting (copy mode) |
|
54 |
User auto color calibration (color balance adjustment) Inhibit/Allow setting (printer mode) |
|
69 |
Used to set the operating conditions for toner near end. |
|
73 |
Used to set Toner save setting. |
|
27 |
2 |
Used to set the sender's registration number and the HOST server telephone number. (FSS function) |
|
4 |
Used to set the initial call and toner order auto send. (FSS function) |
|
7 |
Used to set of the enable, alert callout. (FSS function) |
|
14 |
Used to set the FSS function connection test mode. |
|
15 |
Used to display the FSS connection status. |
|
16 |
Used to set the FSS alert send. |
|
30 |
1 |
Used to check the operations of the sensors and the detectors in other than the paper feed section and the control circuits. |
|
43 |
1 |
Used to set the fusing reference temperature of each operation mode. |
|
4 |
Used to set the fusing temperature 2 in each mode. (Continued from SIM 43-1.) |
|
20 |
Used to set the environmental correction under low temperature and low humidity (L/L) for the fusing temperature setting (SIM 43-1) in each paper mode. |
|
21 |
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (SIM 43-1) in each paper mode. |
|
22 |
Used to set the environment correction under low temperature and low humidity (L/L) for the fusing temperature setting (SIM 43-4) in each paper mode. |
|
23 |
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (SIM 43-4) in each paper mode. |
|
24 |
Used to set the correction of the temperature adjustment value of SIM 43-1 and 43-4. |
|
44 |
1 |
Used to set each correction operation function in the image forming (process) section. |
Image process (Photoconductor/ Developing/Transfer/Cleaning) |
2 |
Used to adjust the sensitivity of the image density sensor (registration sensor). |
Process |
4 |
Used to set the conditions of the high density process control operation. |
Process |
6 |
Used to execute the high density process control forcibly. |
Process |
9 |
Used to display the result data of the high density process control operation. |
Image process (Photoconductor/ Developing/Transfer/Cleaning) |
12 |
Used to display the operation data of the high density process control and the image density sensor (registration sensor). |
Image process (Photoconductor/ Developing) |
14 |
Used to display the output level of the temperature and humidity sensor. |
Process (OPC drum, development)/Fusing/LSU |
15 |
Used to display the toner density control data. |
Developing system |
21 |
Used to set the half tone process control target. |
Process |
22 |
Used to display the toner patch density level in the half tone process control operation. |
Process |
24 |
Used to display the correction target and the correction level in the half tone process control operation. |
Process |
25 |
Used to set the calculating conditions of the correction value for the half tone process control. |
Process |
26 |
Used to execute the half tone process control compulsorily. |
Process |
27 |
Used to clear the correction data of the half tone process control. |
Process |
28 |
Used to set the process control execution conditions. |
Process |
29 |
Used to set the operating conditions of the process control during a job. |
Process |
31 |
Used to adjust the OPC drum phase. (Manual adjustment) |
Process |
37 |
Used to set the development bias correction level in the continuous printing operation. |
|
43 |
Used to display the identification information of the developing unit. |
Developing system |
62 |
Used to set the calibration data of the color image sensor (image registration sensor F). |
|