Sharp MX5141N
Simulation mode. List of codes 1-22
Main | Sub | Functions | Section |
---|---|---|---|
1 | 1 | Used to check the operation of the scanner (reading) unit and the control circuit. | Scanner (reading) |
2 | Used to check the sensors in the scanner (reading) section and the related circuits. | Scanner (reading) | |
5 | Used to check the operation of the scanner (reading) unit and the control circuit. | Scanner (reading) | |
2 | 1 | Used to check the operations of the automatic document feeder and the control circuit. | DSPF/RSPF |
2 | Used to check the operations of the sensors and the detectors in the automatic document feeder section and the control circuits. | DSPF/RSPF | |
3 | Used to check the operations of the loads in the automatic document feeder and the control circuit. | DSPF/RSPF | |
3 | 2 | Used to check the operations of the sensors and the detectors in the finisher and the control circuit. | Finisher |
3 | Used to check the operation of the load in the finisher and the control circuit. | Finisher | |
10 | Used to adjust the finisher. | Finisher | |
4 | 2 | Used to check the operations of the sensors and detectors in the desk/large capacity tray (LCC), and the control circuit of those. | Desk/Large capacity tray (LCC) |
3 | Used to check the operations of the loads in the desk/large capacity tray (LCC), and the control circuit of those. | Desk/Large capacity tray (LCC) | |
5 | Used to check the operations of the paper feed desk paper transport clutch (DTRC) and the LCC paper transport clutch (LTRC). | Desk/Large capacity tray (LCC) | |
5 | 1 | Used to check the operation of the display, LCD in the operation panel, and control circuit. | Operation panel |
2 | Used to check the operation of the heater lamp and the control circuit. | Fusing | |
3 | Used to check the operation of the scanner lamp and the control circuit. | Scanner (reading) | |
4 | Used to check the operation of the discharge lamp and the control circuit. | Process | |
6 | 1 | Used to check the operations of the load in the paper transport system (clutches and solenoids) and the control circuits. | Paper transport/Paper exit section |
2 | Used to check the operations of each fan motor and its control circuit. | Others | |
3 | Used to check the operations of the transport unit and the control circuit. | Process (Transport) | |
6 | Used to perform fusing pressure release and applying, and to check the operations of the control circuits. | Fusing | |
90 | Used to reset the machine to the factory setting. (The scanner is set to the lock enable position) | Scanner | |
7 | 1 | Used to set the operating conditions of aging. | Others |
6 | Used to set the operating intermittent aging cycle. | ||
8 | Used to display the warm-up time. | ||
9 | Color setting in the color copy test mode (Used to check the copy operation and the image quality for each color). | ||
12 | The document reading number of sheets setting (for aging operation) | DSPF/RSPF | |
8 | 1 | Used to check and adjust the operations of the developing voltage in each print mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. | Process (Developing) |
2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. | Process (Charging) | |
6 | Used to check and adjust the operation of the transport voltage and the control circuit. | Process (Transport) | |
9 | 2 | Used to check the operations of the sensors and detectors in the paper reverse section (duplex section) and its control circuit. | Duplex |
3 | Used to check the operations of the load in the paper reverse section (duplex section) and its control circuit. | Duplex | |
10 | 1 | Used to check the operations of the toner supply mechanism (toner motor) and the related circuit. | Process (Developing) |
13 | - | Used to cancel the self-diag "U1" trouble. | |
14 | - | Used to cancel the self-diag H3, H4, H5 troubles. | |
15 | - | Used to cancel the self-diag "U6" trouble. | LCC |
16 | - | Used to cancel the self-diag "U2" trouble. | MFP PWB / PCU PWB / SCU PWB |
17 | - | Used to cancel the self-diag "PF" trouble. | |
21 | 1 | Used to set the maintenance cycle. | |
22 | 1 | Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) | |
2 | Used to check the total number of misfeed and troubles. (When the number of total jam is considerably great, it is judged as necessary for repair.) | ||
3 | Used to check misfeed positions and the misfeed count of each position. * Presumption of the faulty point by this data is possible. |
||
4 | Used to check the trouble (self diag) history. | ||
5 | Used to check the ROM version of each unit (section). | Firmware | |
6 | Used to output the setting/adjustment data (simulation, FAX soft switch, counter), the firmware version, and the counter list. | ||
8 | Used to check the number of operations (counter value) of the finisher, the DSPF/RSPF, and the scan (reading) unit. | ||
9 | Used to check the number of use (print quantity) of each paper feed section. | Paper feed, ADU, LCC | |
10 | Used to check the system configuration (option, internal hardware). | ||
11 | Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed) | FAX | |
12 | Used to check the DSPF/RSPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is considerably great, it can be judged as necessary for repair.) | DSPF/RSPF | |
13 | Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge) and the fusing unit | Process | |
14 | Used to display the use status of the toner cartridge. | Process | |
18 | Used to display the user data delete history. | ||
19 | Used to check the values of the counters related to the scan - image send. |