Sharp MX3631
Simulation mode. List of Classic mode. Codes 1-1 - 22-2
Sim No. | Function | Easy Mode | ||
---|---|---|---|---|
Installation | Maintenance | Adjustment and Settings | ||
1-1 | Check the operation of the scanner (reading) unit and the control circuit | |||
1-2 | Check the operation of the sensors in the scanner (reading) section and the control circuit | |||
1-5 | Check the operation of the scanner (reading) unit and the control circuit | |||
2-1 | Check the operation of the document feeder and the control circuit | |||
2-2 | Check the operation of the sensors in the document feeder section and the control circuit |
|||
2-3 | Check the operation of the loads in the document feeder and the control circuit | |||
3-2 | Check the operation of the sensors in the finisher and the control circuit | |||
3-3 | Check the operation of the load in the finisher and the control circuit | |||
3-10 | Adjust the finisher | 4 | ||
4-2 | Check the operation of the sensors in the desk/large capacity tray (LCC) and the control circuit | |||
4-3 | Check the operation of the loads in the desk/ large capacity tray (LCC) and the control circuit | |||
4-5 | Check the operation of the paper transport clutch (DTRC) in the desk and the LCC paper transport clutch (LTRC) | |||
5-1 | Check the operation of the display, LCD in the operation panel and the control circuit | |||
5-2 | Check the operation of the heater lamp and the control circuit | |||
5-3 | Check the operation of the scanner lamp and the control circuit | |||
5-4 | Check the operation of the discharge lamp and the control circuit | |||
6-1 | Check the operation of the load in the paper transport system (clutches and solenoids) and the control circuit | |||
6-2 | Check the operation of each fan motor and the control circuit | |||
6-3 | Check the operation of the transport unit and the control circuit | |||
6-6 | Check the operation of fusing pressure release, applying and the control circuit | |||
6-90 | Reset the machine to the factory setting (The scanner is set to the lock enable position) | 6 | ||
7-1 | Set the operating conditions of againg | |||
7-6 | Set the operating intermittent aging cycle | |||
7-8 | Display the warm up time | |||
7-9 | Color setting in the color copy test mode (check the copy operation and the image quality for each color) | |||
7-12 | Set the document reading number of sheets | |||
8-1 | Check and adjust the operation of the developping voltage in each print mode and the control circuit. *When the middle speed is adjusted the low speed is also adjusted simultaneously | |||
8-2 | Check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. *When the middle speed is adjusted the low speed is also adjusted simultaneously | |||
8-6 | Check and adjust the operation of the transport voltage and the control circuit | |||
8-10 | Set main charger current output | |||
9-2 | Check the operation of the sensors in the paper reverse section (duplex section) and the control circuit | |||
9-3 | Check the operation of the load in the paper reverse section (duplex section) and the control circuit | |||
10-1 | Check the operation of the toner supply mechanism (toner motor) and the control circuit | |||
10-3 | Check the operation of the toner cartridge ejecting position sensor and the control circuit | 6 | 2-5 | 2 |
13 | Cancel U1 trouble | 5 | 6 | |
14 | Cancel H3, H4, H5 troubles | 5 | 6 | |
15 | Cancel U6 trouble | 5 | 6 | |
16 | Cancel U2 trouble | 5 | 6 | |
21-1 | Set the maintenance cycle | 4 | ||
22-1 | Check print count in each section and each operation mode | 3-1 | 1-1 | 9-1 |
22-2 | Check total count of misfeed and troubles |