Sim No. |
Function |
46 |
24 |
Adjust copy gray balance (auto adjustment) |
32 |
Adjust the document background density reproducibility in the auto mode |
37 |
Adjust the reproducibility capability of gray image creation |
39 |
Adjust the sharpness of send image |
40 |
Adjust the FAX send image density (all modes) |
41 |
Adjust the FAX send image density (normal) |
42 |
Adjust the FAX send image density (fine) |
43 |
Adjust the FAX send image density (super fine) |
51 |
Adjust the gamma of heavy paper mode and image process mode in the copy mode |
52 |
Set gamma default value of heavy paper mode and image process mode in the copy mode |
54 |
Adjust the engine halftone auto density (dither) |
48 |
1 |
Adjust the scan image magnification ratio (main scanning direction and sub scanning direction) |
6 |
Adjust the rotation speed of each motor |
49 |
1 |
Update the firmware |
50 |
1 |
Adjust the copy image position and the image loss |
5 |
Adjust the printer image position and the image loss |
6 |
Adjust SPF image position and the image loss |
10 |
Adjust the image position in the each paper feed tray |
12 |
Adjust the scan image off center position |
51 |
1 |
Set the transfer voltage timing |
2 |
Adjust the contact pressure on paper by the main unit and the SPF resist roller |
53 |
8 |
Adjust the document lead edge and the scan position |
9 |
Set the dirt detection and scan position |
10 |
Execute SPF dirt detection |
55 |
1 |
Set the specification of the engine operation |
2 |
Set the specification of the scanner operation |
3 |
Set the specification of the controller operation |
10 |
Used to set the special stamp text for Taiwan |
56 |
2 |
Backup the data in the EEPROM and STORAGE to the USB memory |
5 |
Backup the SIM22-6 data in the text format to the USB memory |
60 |
1 |
Check read/write memory operation |
61 |
1 |
Check the LSU polygon motor rotation and laser detection |
3 |
Set the laser power |
63 |
1 |
Check shading correction data |
2 |
Execute shading correction |
3 |
Adjust scanner (CCD) color balance and gamma correction |
5 |
Reset the scanner (CCD) color balance and gamma correction |
12 |
B/W image create adjustment |
64 |
2 |
Test print |
4 |
Printer test print |
5 |
Printer test print (PCL) |
6 |
Printer test print (PS) |
65 |
10 |
KEY time setting display |
66 |
1 |
Set the specification of image send operation |
2 |
Set country code |
4 |
Check signal output level (max) |
7 |
Used to output all image data saved in the image memory |
8 |
Used to send the selected sound message to the line and the speaker (max) |
10 |
Used to clear the FAX and image send image data |
11 |
Used to send the selected signal at 300bps to the line and the speaker (max) |
13 |
Used to register dial number for Sim66-14/15/16 dial test |
17 |
Used to send the DTMF signal to the line and the speaker (max) |
21 |
Used to print the selected iyems (system error, protocol monitor) |
30 |
Used to display the TEL/LIU status change, the display is highlighted by status change |
31 |
Used to set ON/OFF the port for output to TEL/LIU |
32 |
Used to check the fixed data received from the line and to display the result |
33 |
Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected the display is highlighted |
34 |
Communication time display |
66 |
52 |
Pseudo ringer check |
67 |
25 |
Adjust printer gray balance (manual) |
31 |
Clear printer calibration data |
33 |
Adjust printer screen gamma |
34 |
Set the density correction of printer high density area |
36 |
Adjust the density in the printer low density area |
52 |
Set gamma default value of the printer screen |