Riso SF9390
Test Mode. List of Test Modes 0152 - 0172
| No. | Name | Description | Setting |
|---|---|---|---|
| 0152 | "Lighten print" display control |
Specifies whether to display "Lighten print" in Functions and Custom Setting Mode. | Setting value 0: Not display <default> 1: Display |
| 0153 | Special Paper Ctrl Enable Control |
Specifies whether to display "Properties" - "Special Paper Ctrl". | Setting value 0: Not display <default> 1: Display |
| 0154 | Min. Print Quantity Control | Sets whether to allow the "Minimum Print Q'ty" setting in Custom Setting Mode and Properties to be edited. |
Setting value: 0: Uneditable 1: Editable <default> |
| 0155 | Counter Action Control | Enables/Disables the copy and master counters (solenoid counter and software counter). * This setting is reset to the default when the power is turned off. |
Setting value: 0: Counter disabled 1: Counter enabled <default> |
| 0159 | "Warning" Display Control | Specifies whether to display a size warning (F02, F10, or F43) at the start of master making or printing. | Setting value: 0: Display the warning 1: Not display the warning <default> |
| 0160 | Auto Multi-Up Recovery | Specifies whether to reactivate the Multi-Up Print setting after a Multi-Up Print operation is completed while the Auto Process function is OFF. | Setting value: 0: Do not reactivate (The Multi-Up Print setting stays OFF) <default> 1: Reactivate |
| 0161 | Program Print Repeat Setting |
Specifies whether to retain the Single Page Mode setting when the Auto Process function is OFF. |
Setting value 0: Do not retain <default> 1: Retain |
| 0162 | M-M Standby Period Setting |
When the Master Making mode is selected, the master making standby conditions (TPH pressure, clamp opening position, and scanner lamp ON) are kept for the period of time specified here. If this is set to 60 seconds or less, the THP, clamp, and scanner standby conditions are cancelled when the specified period of time elapses. If this is set to a value greater than 60 seconds, the scanner standby condition is cancelled when 60 seconds elapse and the THP and clamp standby conditions are cancelled when the specified period of time elapses. |
Setting value: 0 to 180 (0s (= No standby) to 180s) Default: 180 (180s) Unit: 1 (1s) |
| 0165 | RLP Mode Switch Timing Control |
Sets the display change timing for cases where the RLP auto-selection mode is used. | Setting range: -5 to +5 (0s to 2.5s) Unit: 1 (0.25s) Default: 0 (1.25s) |
| 0166 | Max. Print Quantity Control | Enables/Disables the maximum print quantity setting, and also sets the maximum print quantity. | Setting range: 0 to 9999 prints (The entered value must be 0 to 9999.) Unit: 1 (1 print) Default: 0 (0 print: The maximum print quantity setting is disabled.) |
| 0167 | Paper ID Auto-Repeat Control |
Specifies whether to reset the paper size settings to the default or keep the current settings when the power is turned off or the all-reset operation is performed. | Setting: 0: Keep the current paper size settings <default> 1: Reset the paper size settings to the default |
| 0168 | Fine Adjust Button on Display |
Sets whether or not to display the Fine Adjust button. | Setting: 0: Keep the current paper size settings <default> 1: Reset the paper size settings to the default |
| 0169 | "Properties" Display Control | Specifies whether to display the Properties tab. | Setting value: 0: Not display 1: Display <default> |
| 0170 | Consumable Storage Indication | Specifies whether to display the Stock Management item on the Properties tab. | Setting value: 0: Not display <default for overseas> 1: Display <default for Japan> |
| 0171 | Clock Setting (YEAR) | Sets the year part of the date in the RTC. * When this test starts, the year of the current RTC date appears on the seven-segment display. For example, "2002" appears for the year of 2002. * Test Mode No.0101 (Clock Adjustment Confirm) must be run after values are set in Test Modes No.0171 - No.0173. Test Mode No.0101 applies values set in Test Modes No.0171 - No.0173 to the RTC. |
Setting range: 2000 to 2099 Unit: 1 (year) Default: 2000 when the RTC has not yet been set (before No.0101 runs) The RTC value at the start of the test when the RTC has already been set (after No.0101 runs) |
| 0172 | Clock Setting (MONTH & DATE) | Sets the month and day parts of the date in the RTC. * When this test starts, the month and day of the current RTC date appear on the seven-segment display. For example, "1001" appears for October 1st. * Test Mode No.0101 (Clock Adjustment Confirm) must be run after values are set in Test Modes No.0171 - No.0173. Test Mode No.0101 applies values set in Test Modes No.0171 - No.0173 to the RTC. |
Setting range: First two digits: 1 to 12 (January to December) Last two digits: 1 to 31 (1st to 31st) Unit: 1 Default: 0101 when the RTC has not yet been set (before No.0101 runs) The RTC value at the start of the test when the RTC has already been set (after No.0101 runs) |