PrintCopy.info service

Riso SF5130

 All About this machine
Table Of Contents 

Test Mode. List of Test Modes 0084 - 0087

Unit No. Name Description Setting Model
SF9 SF5*5 SF5*3
Sys /
Panel		 0084 Test Print E (Dot1 +Crossed Lines) Creates Test pattern 6 (Dot 1 + Crossed Lines).
The size of the crossed line pattern is 128 dots (10.8mm) * 128 dots (5.4mm), where the width of a line is 1 dot (0.084mm) * 1 dot (0.042mm).
+
The dot pattern where the size of a black dot is 8 dots (0.68mm) * 8 dots (0.34mm)
  1. For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  2. The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 - × о о
Sys /
Panel		 0084 Test Print E (Dot1 +Crossed Lines) Creates Test pattern 6 (Dot 1 + Crossed Lines).
The size of the crossed line pattern is 128 dots (5.4mm) * 128 dots (5.4mm), where the width of a line is 1 dot (0.042mm) * 1 dot (0.042mm).
+
The dot pattern where the size of a black dot is 8 dots (0.34mm) * 8 dots (0.34mm)
  1. For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  2. The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 - о × ×
Sys /
Panel		 0085 Test Print F (Dot2+Crossed Lines) Creates Test pattern 7 (Dot 2 + Crossed Lines).
The size of the crossed line pattern is 128 dots (10.8mm) * 128 dots (5.4mm), where the width of a line is 1 dot (0.084mm) * 1 dot (0.042mm).
+
The dot pattern where the size of a black dot is 16 dots (1,35mm) *
16 dots (0.68mm)
  1. For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  2. The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 - × о о
Sys /
Panel		 0085 Test Print F (Dot2+Crossed Lines) Creates Test pattern 7 (Dot 2 + Crossed Lines).
The size of the crossed line pattern is 128 dots (5.4mm) * 128 dots (5.4mm), where the width of a line is 1 dot (0.042mm) * 1 dot (0.042mm).
+
The dot pattern where the size of a black dot is 16 dots (0.68mm) *
16 dots (0.68mm)
  1. For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  2. The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 - о × ×
Sys /
Panel		 0086 Test Print G (Dot3) Creates Test pattern 8 (Dot 3).
The dot pattern where the size of a black dot is 2 dots (0.169mm) * 2dots (0.084mm)
  1. For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  2. The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 - × о о
Sys /
Panel		 0086 Test Print G (Dot3) Creates Test pattern 8 (Dot 3).
The dot pattern where the size of a black dot is 2 dots (0.084mm) * 2dots (0.084mm)
  1. For the printing pressure, the settings from No.1248 (Printing pressure for Test Mode) must be applied.
  2. The printed image must be cut for the paper size (The cut amount is the same as in normal mode).
 - о × ×
Sys /
Panel		 0087 Paper Feed Test (Cycle) Performs the continuous printing action.
Speed 1: 60rpm, Speed 2: 80rpm, Speed 3: 100rpm, Speed 4: 120rpm, Speed 5: 130rpm, High Speed: 150rpm
  1. The speed key is enabled.
  2. The vertical print positioning key is enabled.
  3. The action starts when the rear cover set switch is pressed. When the Start key is pressed, 10 seconds are waited until the rear cover set switch is pressed (A beep sounds until the set switch is pressed).
 - о о о

 

 

 

Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us