Ricoh D017 MP2550B R-C5
Service Program Mode. SP1-XXX (Feed) 1
1001* | Leading Edge Registration | |
1001 1 | Paper Tray Feed | Adjusts the printing leading edge registration from each paper feed station using the Trimming Area Pattern (SP2902-003 No. 10). [+9.0 —9.0 / +0.0 / 0.1 mm/step] Use the © key to toggle between + and - before entering the value. The specification is 3 ± 2 mm. See "Replacement and Adjustment - Copy Adjustment" for details. |
1001 2 | By-pass Feed | |
1001 3 | Duplex, Side2 |
1002* | Side-to-Side Registration | |
1002 1 | Tray 1 | Adjusts the printing side-to-side registration from each paper feed station using the Trimming Area Pattern (SP2902-003 No. 10). [+9.0 —9.0 / +0.0 / 0.1 mm/step] Use the © key to toggle between + and - before entering the value. The specification is 2 ±1.5 mm. See "Replacement and Adjustment - Copy Adjustment" for details. |
1002 2 | Tray 2 | |
1002 3 | Tray 3 (Optional PFU Tray 1, or LCT) | |
1002 4 | Tray 4 (Optional PFU Tray 2) | |
1002 5 | By-pass | |
1002 6 | Duplex Side 2 |
1003* | Paper Feed Timing | |
1003 1 | Tray 1 | Adjusts the paper feed clutch timing at registration. The paper feed clutch timing determines the amount of paper buckle at registration. (A larger setting leads to more buckling.) [0 ~ 10 / 5 / 1 mm/step] |
1003 2 | Tray 2/3/4 By-pass | |
1003 3 | Duplex Side 2 | [0 ~ 20 / 6 / 1 mm/step] |
1103 | Fusing Idling |
Switches fusing idling on/off. [0 = Off / 1 = On / 2 = Off plus machine temperature check] Switch on if fusing on the 1st and 2nd copies is incomplete (this may occur if the room is cold.) |
1105* | Fusing Temperature Adjustment | |
1105 1 | Roller Center | Adjusts the fusing temperature at the center and both ends of the hot roller for normal printing. [120 ~ 200 / 180 / 1 °C/step] |
1105 2 | Roller Ends | |
1105 3 | Energy Saver | Adjusts the fusing temperature at the center and both ends of the hot roller for energy saver mode. [0 ~ 160 / 150 / 1 °C/step] |
1105 4 | Thick Paper - Center | Adjusts the additional fusing temperature for thick paper for the 2nd paper tray and for the bypass tray. [0 ~ 30 / 15 / 1 °C/step] |
1105 5 | Thick Paper - Ends | |
1105 6 | After Warming-up - Center | Adjusts the fusing temperature at the center of the hot roller after the machine has warmed up. [120 ~ 200 / 180 / 1 °C/step] |
1105 7 | After Warming-up - Ends | Adjusts the fusing temperature at both ends of the hot roller after the machine has warmed up. [120 ~ 200 / 185 / 1 °C/step] |
1105 8 | After Warming-up - No. of Pages |
In this machine, fusing temperature is kept 10°C higher than the normal temperature for a number of pages after the machine has warmed up. This SP selects the number of pages made at this temperature. See Detailed Section Descriptions - Fusing for more details. [0 ~ 10 / 3 / 1 page/step] |
1105 9 | After Warming-up - Times | In this machine, fusing temperature is kept 10°C higher than the normal temperature for a short while after the machine been warmed up. This SP selects the length of time that this temperature is used. See Detailed Section Descriptions - Fusing for more details. [0 ~ 180 / 60 / 1s/step] |
1106 | Fusing Temp. Display | |
1106 1 | Roller Center | Displays the fusing temperature for the center or both ends of the hot roller. |
1106 2 | Roller Ends | |
1106 3 | In the Machine at Power On | Displays the temperature in the machine at power on. This temperature is monitored by the thermistor on the SBCU board. |
1108* | Fusing Soft Start Setting |
Selects whether the fusing temperature control cycle is 1 or 3 seconds. If this is "1 (3 s)", the power supply fluctuation caused by the fusing lamp turning on is less often. [0 = 1 s / 1 = 2 s] Default: 0 = N. America, Taiwan, 1 = Europe/Asia |
1109 | Fusing Nip Band Check |
Checks the fusing nip band [1 = Start / 0 = Stop] |