Ricoh D010 MP2500 PR-C1

The following codes are used:

• Asterisk (*): The settings are saved in the NVRAM. Most of them return to the default values when you execute SP 5801-2
• The DFU menu is for design or factory use only. You must not change the settings.
• Brackets ([ ]): The brackets enclose the setting rage, default value, and minimum step (with unit) as follows: [Minimum to Maximum / Default / Step].
• SSP: The program is in the SSP Mode only. Consult your supervisor before you use this program.

SP1-XXX (Feed)

1001*	Leading Edge Registration
	Adjusts the printing leading-edge registration from paper trays.
1001 1	All Trays	[-9.0 to 9.0 / 0.0 / 0.1 mm/step] (* "Copy Adjustments Printing/Scanning")
1001 2	By-pass
1001 3	Duplex

 

1002*	Side-to-Side Registration
	Adjusts the printing side-to-side registration from each paper feed station, using the Trimming Area Pattern (SP 5902, No.10). Adjustments are supported for all 4 possible feed trays (including optional trays). The SP 1002-1 setting is applied to all trays, not just the 1st tray. Settings for trays 2 to 4 are offsets relative to the SP 1002 1 setting. For duplex copies, the value for the front side is determined by SP 1002-1 to -4, and the value for the rear side is determined by SP 1002-6.
1002 1	1st tray	[-9.0 to 9.0 / 0.0 / 0.1 mm/step] (* "Copy Adjustments Printing/Scanning")
1002 2	2nd tray
1002 3	3rd tray
1002 4	4th tray
1002 5	By-pass
1002 6	Duplex

 

1007	Display By-pass
1007 1	Display By-pass	Displays the by-pass paper width switch output.

 

1103*	Fusing Idling
	This program decides the action of the Fusing Drive Release Mechanism. When you select "1," the contact/release control is disabled and the drive power is always transmitted to the fusing unit. As a result, the machine takes a longer time to warm up the fusing unit. Use SP 1103-1 if fusing quality is low even when the room temperature is not very low.
1103 1	Fusing Idling	[0 = No / 1 = Yes]

 

1105*	Fusing Temperature Adjustment
	Adjusts the target fusing temperature. "Center" indicates the center of the roller; "End" indicates the front and rear ends.
1105 1	Warm Up-Center	[140 to 180 / 170 / 1°C/step]
1105 2	Warm Up-End
1105 3	Standby-Center	[140 to 170 / 165 / 1°C/step]
1105 4	Standby-End	[140 to 165 / 165 / 1°C/step]
1105 5	Copying-Center	[140 to 165 / 165 / 1°C/step]
1105 6	Copying-End
1105 7	Low Level 2-Center	[0 to 80 / 60 / 1°C/step]
1105 8	Low Level 2-End
1105 9	Thick-Center	[140 to 185 / 185 / 1°C/step]
1105 10	Thick-End
1105 11	Warm Up Low-Center	[140 to 180 / 180 / 1°C/step]
1105 12	Warm Up Low-End
1105 13	Copy-Low-Center	[140 to 185 / 185 / 1°C/step]
	Adjusts the target fusing temperature for the center of the roller when the inside temperature of the machine is 18C or less.
1105 14	Copy-Low-End	[140 to 185 / 185 / 1°C/step]
	Adjusts the target fusing temperature for the end of the roller when the inside temperature of the machine is 18C or less.
1105 15	Low-Temp-Time-1	[0 to 60 / 60 / 1 second/step]
	Adjusts the threshold time for the 1st temperature decrement. When the time of the first copy/print reaches this threshold, the target temperature is decreased by 5°C from the temperature specified with SP1105-13, -14.
1105 16	Low-Temp-Time-2	[61 to 120 / 120 / 1 second/step]
	Adjusts the threshold time for the 2nd temperature decrement. When the time of the first copy/print reaches this threshold, the target temperature is decreased by 10°C from the temperature specified with SP1105-13, -14.
1105 17	Low-Temp-Time-3	[121 to 240 / 240 / 1 second/step]
	Adjusts the threshold time for the 3rd temperature decrement. When the time of the first copy/print reaches this threshold, the target temperature is decreased by 15°C from the temperature specified with SP1105-13, -14.