Sub item |
Description |
FRT-TS-C |
Transfer bias front side setting value (C) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value.
- Increase the setting value. (Effective for toner scatter/dotted image)
- Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
- It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]
|
FRT-TS-K |
Transfer bias front side setting value (Bk) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value.
- Increase the setting value. (Effective for toner scatter/dotted image)
- Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
- It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]
|
BCK-TR-Y |
Transfer bias backside setting value (Y) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value.
- Increase the setting value. (Effective for toner scatter/dotted image)
- Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
- It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]
|
BCK-TR-M |
Transfer bias backside setting value (M) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value.
- Increase the setting value. (Effective for toner scatter/dotted image)
- Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
- It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]
|
BCK-TR-C |
Transfer bias backside setting value (C) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value.
- Increase the setting value. (Effective for toner scatter/dotted image)
- Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
- It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]
|
BCK-TR-K |
Transfer bias backside setting value (Bk) [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value.
- Increase the setting value. (Effective for toner scatter/dotted image)
- Decrease the setting value. (Effective for white dots/white flower patches/image with high granularity in halftone mode) Setting range: -30 to 40 (Unit: 50V)
- It is preferable to enter values in the condition of "M <= C <= Y <= K". [Factory setting value/Value after RAM clearing: 0]
|
PGR-YMCK |
Setting value of transfer bias between sheets (Y, M, C, Bk) [When used]
The density of the entire area of 70 to 80mm from the leading edge of the sheet is low/high, or there are an infinite number of white or black spots in an image when the entire print is halftone, etc.
[Adjustment method]
- The problem may be eliminated by changing the setting value.
- Increase the setting value. (Effective for thin density in the area 70 to 80mm from the leading edge)
- Decrease the setting value. (Effective for high density in the area 70 to 80mm from the leading edge) Setting range: -20 to 50 (Unit: 50V)
[Factory setting value/Value after RAM clearing: 0] |
FRT-ATH |
Attraction bias front side setting value [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value. Setting range: -20 to 20 (Unit: 100V)
[Factory setting value/Value after RAM clearing: 0] |
BCK-ATH |
Attraction bias backside setting value [When used]
An image failure occurs depending on the type or condition of the paper AND the problem cannot be eliminated by performing special printing process.
[Adjustment method]
- The problem may be eliminated by changing the setting value. Setting range: -20 to 20 (Unit: 100V)
[Factory setting value/Value after RAM clearing: 0] |
FRFS-TMP |
Fixing temperature front side setting value [When used]
The problem cannot be eliminated by performing special printing process and the image is not firmly fixed to the sheet, or a residual image remains in the image.
[Caution] The fixing heater temperature is changed via this mode, and therefore, attentions should be paid when using this mode. [Adjustment method]
- When an image is not firmly fixed to the sheet, the problem may be eliminated by increasing the setting value.
- When a residual image remains in an image, the problem may be eliminated by decreasing the setting value. Setting range: -4 to 4 (Unit: Approx. 5 degree C)
[Factory setting value/Value after RAM clearing: 0] |
BKFS-TMP |
Fixing temperature backside setting value [When used]
The problem cannot be eliminated by performing special printing process and the image is not firmly fixed to the sheet, or a residual image remains in the image.
[Caution] The fixing heater temperature is changed via this mode, and therefore, attentions should be paid when using this mode. [Adjustment method]
- When an image is not firmly fixed to the sheet, the problem may be eliminated by increasing the setting value.
- When a residual image remains in an image, the problem may be eliminated by decreasing the setting value. Setting range: -4 to 4 (Unit: Approx. 5 degree C)
[Factory setting value/Value after RAM clearing: 0] |