Canon imageRUNNER Advance C351iF
Troubleshooting. Jam Code. Detailed 5 Finisher
| ACCID | Jam | Type | Sensor Name | Sensor ID | Jam description | I/O | |||
|---|---|---|---|---|---|---|---|---|---|
| Code | Address | bit | Remarks | ||||||
| 02 | 1001 | Delay | Buffer Sensor | S1 | Description | Detected when the Buffer Sensor (S1) does not detect paper after lapse of the specified time since reception of a paper delivery signal from the host machine. | - | - | |
| 1301 | Power ON | Buffer Sensor | S1 | Description | Detected when the Buffer Sensor (S1) detects paper during power-on. | - | - | - | |
| 1401 | Door open | Buffer Sensor | S1 | Description | Detected when the front door is opened while paper is being fed (the Buffer Sensor (S1) detects paper). | - | - | ||
| 1F01 | Early arrival jam | Buffer Sensor | S1 | Description | Detected when the Buffer Sensor (S1) detects paper without receiving a delivery signal from the host machine. Or detected when the Buffer Sensor (S1) detects paper earlier than the specified timing after reception of a delivery signal from the host machine. |
||||
| 1004 | Delay | Feed Path Sensor | S2 | Description | Detected when the Feed Path Sensor (S2) does not detect paper after lapse of the specified time since detection of paper by the Buffer Sensor (S1). | - | - | ||
| 1104 | Staionary | Feed Path Sensor | S2 | Description | Detected when the Feed Path Sensor (S2) does not turn off after lapse of the specified time since detection of paper by the Feed Path Sensor (S2). | - | - | ||
| 1304 | Power ON | Feed Path Sensor | S2 | Description | Detected when the Feed Path Sensor (S2) detects paper during power-on. | - | - | - | |
| 1404 | Door open | Feed Path Sensor | S2 | Description | Detected when the front door is opened while paper is being fed (the Feed Path Sensor (S2) detects paper). | - | - | ||
| 1500 | Stapler | Staple HP Sensor | S11 | Description | Detected when the staple HP sensor (S11) cannot detect the stapler again even after the specified time has lapsed since the stapler passed through the staple HP sensor (S11) when stapling is executed. Or detected when the staple edging sensor (S12) cannot detect a staple even when recovery operation is performed ten times when staple edging is executed. |
||||
| 2F30 | Error avoidance |
Front Alignment Motor | Description | When the controller detected the following errors during feeding operation. Error in the front alignment motor (E530) |
- | - | |||
| 2F31 | Error avoidance |
Staple Motor | Description | When the controller detected the following errors during feeding operation. Error in the staple motor (E531) |
- | - | |||
| 2F37 | Error avoidance |
Rear Alignment Motor |
Description | When the controller detected the following errors during feeding operation. Error in the rear alignment motor (E537) |
- | - | |||
| 2F40 | Error avoidance |
Stack Tray Shift Motor | Description | When the controller detected the following errors during feeding operation. Error in the stack tray shift motor (E540) |
- | - | |||
| 2F75 | Error avoidance |
Gripper Motor | Description | When the controller detected the following errors during feeding operation. Error in the gripper motor (E575) |
- | - | |||
| 2F77 | Error avoidance |
Paddle Motor | Description | When the controller detected the following errors during feeding operation. Error in the paddle motor (E577) |
- | - | |||
| 2F83 | Error avoidance |
Tray Auxiliary Guide Motor | Description | When the controller detected the following errors during feeding operation. Error in the tray auxiliary guide motor (E583) |
- | - | |||