Canon iR Advance C9280 Pro
Troubleshooting. Jam Code. Image Reader-A1
Duplex Color Image Reader-A1 / Color Image Reader-A1
| ACC ID | Jam Code | Type | Sensor Name / Description | Sensor ID |
|---|---|---|---|---|
| 01 | 0001 | DELAY | Post-separation sensor 3 | PCB2 |
| 01 | 0002 | STNRY | Post-separation sensor 3 | PCB2 |
| 01 | 0003 | DELAY | Delay detection sensor | SR4 |
| 01 | 0004 | STNRY | Delay detection sensor | SR4 |
| 01 | 0005 | DELAY | Registration sensor | PCB3 |
| 01 | 0006 | STNRY | Registration sensor | PCB3 |
| 01 | 0007 | DELAY | Lead sensor 1 | PCB4 |
| 01 | 0008 | STNRY | Lead sensor 1 | PCB4 |
| 01 | 0009 | DELAY | Lead sensor 2 | SR5 |
| 01 | 0010 | STNRY | Lead sensor 2 | SR5 |
| 01 | 0011 | DELAY | Delivery sensor | PCB5 |
| 01 | 0012 | STNRY | Delivery sensor | PCB5 |
| 01 | 0042 | STNRY | Post-separation sensor 3 | PCB2 |
| 01 | 0043 | DELAY | Delay detection sensor | SR4 |
| 01 | 0044 | STNRY | Delay detection sensor | SR4 |
| 01 | 0045 | DELAY | Registration sensor | PCB3 |
| 01 | 0046 | STNRY | Registration sensor | PCB3 |
| 01 | 0047 | DELAY | Lead sensor 1 | PCB4 |
| 01 | 0048 | STNRY | Lead sensor 1 | PCB4 |
| 01 | 0049 | DELAY | Lead sensor 2 | SR5 |
| 01 | 0050 | STNRY | Lead sensor 2 | SR5 |
| 01 | 0051 | DELAY | Delivery sensor | PCB5 |
| 01 | 0052 | STNRY | Delivery sensor | PCB5 |
| 01 | 0071 | SEQ NG*2 | - | - |
| 01 | 0073 | ERROR*1 | Disengaging HP sensor 1 | SR15 |
| 01 | 0074 | ERROR*1 | Disengaging HP sensor 2 | SR16 |
| 01 | 0075 | ERROR*1 | Pickup roller unit lifter HP sensor | SR12 |
| 01 | 0090 | ADF OP | DADF open/closed sensor 1/2 | SR1, SR3 |
| 01 | 0091 | ADF OP | DADF open/closed sensor 1/2 | SR1, SR3 |
| 01 | 0092 | COVER OP | Cover open/closed sensor | SR10 |
| 01 | 0093 | COVER OP | Cover open/closed sensor | SR10 |
| 01 | 0094 | RESIDUAL | All feed type sensor | - |
| 01 | 0095 | PICKUP NG | Post-separation sensor 1/2/3 | SR2, SR3, PCB2 |
| 01 | 0096 | LIMITED FUNCTION | - |
*1 The state is recovered by opening and closing the Door, or turning OFF and then ON the power supply. If the same jam is detected although the above operation is performed, an error code will be notified.
*2 The state is recovered by opening and closing the Door, or turning OFF and then ON the power supply. If it is not recovered by the above operation, it is considered an error near the target sensor. Disconnect and then connect the connectors around the target sensor, check if the cable is open circuit, and replace the sensor.