Canon i-SENSYS MF8080Cw
Service Mode. COPIER. FUNCTION. 5 SPLMAN 2
| COPIER > FUNCTION > SPLMAN | ||
|---|---|---|
| SPL50288 | Execution of ITB cleaning failure prevention 2 | |
| Details | E352 To alleviate cleaning failure by increasing the current (bias) applied to the Cleaning Blade and Primary Transfer Roller. E353 To execute cleaning for one round of the ITB after printing 2 sheets. (It becomes 2 sheets intermittent mode.) It is more effective than ICL-IMP. |
|
| Use case | When an image that was on 2 sheets before appears lightly depending on paper type and print pattern (especially high printing ratio) When the trailing edge of paper is soiled |
|
| Adj/set/operate method | Select the item, and then press OK key. | |
| Display/adj/set range | 0 to 1 0: OFF, 1: ON |
|
| Default value | 0 | |
| SPL41971 | Execution of curl prevention mode 1 | |
| Details | To extend the initial rotation time and paper interval, and lower the control temperature. | |
| Use case | When paper which has been printed is curled toward the printed side depending on the paper type, environment (especially in a low humidity environment) or print pattern (especially high printing ratio) | |
| Adj/set/operate method | Select the item, and then press OK key. | |
| Display/adj/set range | 0 to 1 0: OFF, 1: ON |
|
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL69399 | |
| SPL69399 | Execution of curl prevention mode 2 | |
| Details | To lower the fixing temperature when printing thin paper. | |
| Use case | When thin paper which has been printed is curled toward the printed side | |
| Adj/set/operate method | Select the item, and then press OK key. | |
| Display/adj/set range | 0 to 1 0: OFF, 1: ON |
|
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL41971 | |
| SPL35607 | Execution of down sequence prevention mode | |
| Details | To lower the control temperature of the Fixing Assembly without exception. | |
| Use case | When down sequence occurs | |
| Adj/set/operate method | Select the item, and then press OK key. | |
| Caution | Be sure to get approval from the user in advance by explaining that there is a possibility that fixing failure may occur depending on the paper type by lowering the fixing control temperature. | |
| Display/adj/set range | 0 to 1 0: OFF, 1: ON |
|
| Default value | 0 | |
| SPL37510 | ON/OFF of ITB cleaning at paper size mismatch | |
| Details | Normally, when paper other than that of the specified size is fed, ITB cleaning is executed to remove toner. When 1 is set, ITB cleaning is not executed even if paper size is mismatched. Productivity improves, but toner soiling may occur. |
|
| Use case | When paper size is mismatched | |
| Adj/set/operate method | Enter the value, and then press OK key. | |
| Caution | Be sure to get approval from the user by telling that toner soiling may occur to improve productivity. | |
| Display/adj/set range | 0 to 1 0: ON, 1: OFF |
|
| Default value | 0 | |
| SPL65677 | Increase of paper leading edge margin | |
| Details | To increase the margin on the leading edge of paper. As the value is incremented by 1, the margin is increased by 0.1 mm. If the setting is incompatible with SPL68676 (decrease of margin), the setting is disabled (the margin will be standard). |
|
| Adj/set/operate method |
|
|
| Display/adj/set range | 0 to 20 | |
| Unit | 0.1 mm | |
| Default value | 0 | |
| Related service mode | COPIER> FUNCTION> SPLMAN> SPL68676 | |