Canon MF112
Service Mode. TESTMODE
SYSTEM (SYSTEM Test Mode)
DRAM
TESTMODE (Service mode for test print, operation check, etc.) > SYSTEM (SYSTEM Test Mode) > DRAM
TEST1: Checking of data migration
Detail: To check data reading/writing of DRAM area (excluding system work area).
Adj/Set/Operate Method: Press OK key.
Caution: In some cases, the test may take longer time. After performing this test, turn OFF and then ON the power.
SPEAKER
TESTMODE (Service mode for test print, operation check, etc.) > SYSTEM (SYSTEM Test Mode) > SPEAKER
ON: For R&D use
MIN: For R&D use
MAX: For R&D use
SCAN (SCAN Test Mode)
ADJUST
ADF-ADJ
TESTMODE (Service mode for test print, operation check, etc.) > SCAN (SCAN Test Mode) > ADJUST > ADF-ADJ
DF-SPEED: For R&D use
DF-OFFSE: For R&D use
BOOKFEED
TESTMODE (Service mode for test print, operation check, etc.) > SCAN (SCAN Test Mode) > BOOKFEED
PAGE: Display the number of pages
Detail: Display the number of bookfeed pages
Adj/Set/Operate Method: N/A (Display only)
Display/Adj/Set Range: 0 to 1
1: ON (CLOSE)
0: OFF (OPEN)
Default Value: 0
TESTMODE (Service mode for test print, operation check, etc.) > SCAN (SCAN Test Mode) > BOOKFEED
SPEED: Designation of the feeding speed
Detail: Execute feeding test of the book motor at specified speed.
Adj/Set/Operate Method: Select the item, and then press OK key.
Display/Adj/Set Range: TDFAX
FINEFAX
SFINEFAX
RGB600dpi
RGB300dpi
RGB150dpi
Gray600dpi
Gray300dpi
Gray150dpi
Mono600dpi
Mono300dpi
Mono150dpi
START: Start of bookfeed
Detail: To start operation check of the bookfeed.
Adj/Set/Operate Method: Select the item, and then press OK key.
STOP: End of bookfeed
Detail To end operation check of the bookfeed.
Adj/Set/Operate Method Select the item, and then press OK key.
SENSOR
TESTMODE (Service mode for test print, operation check, etc.) > SCAN (SCAN Test Mode) > SENSOR
TRAY PAPER SENS: For R&D use
REGI SENS: For R&D use
ESS DOOR SENS: Cartridge door switch CHECK
Detail: To check for any failure of the Cartridge Door Switch.
Adj/Set/Operate Method: Opening the Cartridge Door changes the displayed value from "1" to "0".
Display/Adj/Set Range 0 to 1
1 : ON (CLOSE)
0 : OFF (OPEN)
ADFTEST
TESTMODE (Service mode for test print, operation check, etc.) > SCAN (SCAN Test Mode) > ADFTEST
SPEED: For R&D use
2-SIDE: For R&D use
COUNT: For R&D use
START: For R&D use
FAX (FAX test mode)
MODEM
TESTMODE (Service mode for test print, operation check, etc.) > FAX (FAX test mode) > MODEM
RELAY-1: For R&D use
FREQ: For R&D use
G3TX: For R&D use
DTMFTX: For R&D use
TESTMODE (Service mode for test print, operation check, etc.) > FAX (FAX test mode) > MODEM
V34G3TX For R&D use
PANEL (PANEL Test Mode)
TESTMODE (Service mode for test print, operation check, etc.) > PANEL (PANEL Test Mode)
KEY CHECK START: KEY CHECK
Detail: To check for any failure of the keys.
Adj/Set/Operate Method: By pressing a key, the corresponding character is hidden in response to the key operation.
Caution: Only the keys controlled by SCNT are checked. The power key is not checked.
Display/Adj/Set Range: The character corresponding to the key is displayed.
LED CHECK START: LED CHECK
Detail: To check for any failure of the LEDs.
Adj/Set/Operate Method: Select the item, and then press OK key.
Caution: Only the LEDs controlled by SCNT are checked. The Power Supply LED is not checked.
Display/Adj/Set Range: Lighting of a job lamp and the alarm lamp
LCD CHECK START: LCD CHECK
Detail: To check for any failure of the LCD.
Adj/Set/Operate Method: Select the item, and then press OK key.
Display/Adj/Set Range: Display a screen confirmation pattern