Zebra 110PAX4 Error Codes List page 1 from 5

  • Code: 01
  • Display: ERROR CONDITION RIBBON OUT
  • Description: Print engine stops; RIBBON light ON, ERROR light flashes.
  • Causes: In thermal transfer mode, ribbon is not loaded or incorrectly loaded. In thermal transfer mode, the ribbon sensor is not detecting ribbon that is loaded incorrectly. In thermal transfer mode, media is blocking the ribbon sensor.
  • Remedy: Load ribbon correctly 1. Load ribbon correctly 2. Calibrate the sensors 1. Load media correctly. 2. Calibrate the sensors
  • Code: 02
  • Display: WARNING RIBBON IN
  • Description: RIBBON light ON, ERROR light flashes.
  • Causes: Ribbon is loaded, but the print engine is set for direct thermal mode.
  • Remedy: Ribbon is not required with direct thermal media. Remove ribbon unless you are using it to protect the printhead. This error message will not affect printing.
  • Code: 03
  • Display: ERROR CONDITION PAPER OUT
  • Description: Print engine stops; MEDIA light ON, ERROR light flashes.
  • Causes: Media is not loaded or is loaded incorrectly. Misadjusted media sensor. The print engine is set for noncontinuous media, but continuous media is loaded.
  • Remedy: Load media correctly. Check position of the media sensor. Install proper media type, or reset print engine for current media type and perform calibration.
  • Code: 04
  • Display: ERROR CONDITION HEAD OPEN
  • Description: Print engine stops and ERROR light flashes.
  • Causes: The head open sensor is not working properly.
  • Remedy: Call a service technician.
  • Code: 05
  • Display: WARNING HEAD TOO HOT
  • Description: Print engine stops and ERROR light flashes.
  • Causes: The printhead is over temperature. Caution • The printhead may be hot enough to cause severe burns. Allow the printhead to cool. Caution • Observe proper electrostatic safety precautions when handling any static-sensitive components such as circuit boards and printheads.
  • Remedy: Printing automatically resumes when the printhead elements cool to an acceptable operating temperature.
  • Code: 06
  • Display: WARNING HEAD COLD
  • Description: Print engine stops and ERROR light flashes.
  • Causes: The printhead is under temperature. The printhead data cable is not properly connected.
  • Remedy: Continue printing while the printhead reaches the correct operating temperature. If the error remains, the environment may be too cold for proper printing. Relocate the print engine to a warmer area. Caution • You must turn off the print engine before performing this procedure. Failure to do so can damage the printhead. 1. Turn off (O) the print engine. 2. Disconnect and reconnect the data cable to the printhead. 3. Ensure that the cable connector is fully inserted into the printhead connector. 4. Turn on (I) the print engine.
  • Code: 07
  • Display: OUT OF MEMORY CREATING BITMAP
  • Description:
  • Causes: Creating Bitmap The bitmap size (label length/width) does not fit in available memory.
  • Remedy: You may do any of the following: 1. With PAUSE on, send a -HM ZPL command to the print engine to display the amount of free memory. Then do one of the following: • Redesign graphic/format to fit available memory or remove items from memory to create more space. • Press PAUSE to skip the formatting step in process and proceed to the next step. 2. With PAUSE on, press CANCEL. The print engine skips the current label formatting process and goes to the next label. 3. Turn the print engine OFF (O) and then ON (I) to clear the print engine’s memory. 4. Upgrade the print engine to a larger memory size.
  • Code: 08
  • Display: OUT OF MEMORY STORING BITMAP
  • Description:
  • Causes: Storing Bitmap Not enough memory is available to store the bitmap created.
  • Remedy: You may do any of the following: 1. With PAUSE on, send a -HM ZPL command to the print engine to display the amount of free memory. Then do one of the following: • Redesign graphic/format to fit available memory or remove items from memory to create more space. • Press PAUSE to skip the formatting step in process and proceed to the next step. 2. With PAUSE on, press CANCEL. The print engine skips the current label formatting process and goes to the next label. 3. Turn the print engine OFF (O) and then ON (I) to clear the print engine’s memory. 4. Upgrade the print engine to a larger memory size.