PrintCopy.info service

Canon LBP3260

Error Codes List page 1

  • Code: 01
  • Display: TONER CARTRIDGE MISSING
  • Description: message appears when it is installed
  • Remedy: 1. The developing bias contact of the high-voltage power supply is not making a good connection with the cartridge contact. Action: If the contacts are dirty, clean them. If the problem continues after cleaning, or parts are deformed or damaged, replace them. 2. Defective cartridge Action: Replace the cartridge. 3. The high-voltage power supply PCB is defective. Action: Replace the high-voltage power supply PCB. 4. The DC controller PCB is defective. Action: Replace the DC controller PCB.
  • Code: 02
  • Display: LOAD <MEDIA> <SIZE> IN MPT
  • Description: message appears when the specified sized paper is in the multi-purpose tray
  • Remedy: 1. Damaged paper detection lever Action: Replace the defective lever. 2. Defective multi-purpose tray paper sensor Action: Replace the multi-purpose tray PCB. 3. The DC controller PCB is defective. Action: Replace the DC controller PCB.
  • Code: 03
  • Display: "LOAD<MEDIA><SIZE> IN UPPER or LOAD<MEDIA><SIZE>IN LOWER
  • Description: when the specified cassette is loaded with paper.
  • Remedy: 1. Pull out the upper and lower cassettes, and install the specified cassette in the printer. If the lifter does not lift, perform step 5 and subsequent steps. 2. Damaged paper detection lever Action: Replace the defective lever. 3. Defective upper cassette paper-out sensor/lower cassette paper-out sensor Action: Replace the pick-up PCB. 4. The DC controller PCB is defective. Action: Replace the DC controller PCB. 5. Pick-up drive unit is damaged. Action: Remove the pick-up unit and replace any damaged parts. 6. The cassette pick-up solenoid is defective. Action: Remove the pick-up unit, and disconnect cassette pick-up solenoid connector J1203 from the pick-up PCB. Measure the resistance between connectors J1203- 1 and J1203-2 on the cable side. If it is not about 160W, replace the cassette pickup solenoid. 7. The pick-up PCB is defective. Action: Replace the pick-up PCB. 8. The DC controller PCB is defective. Action: Replace the DC controller PCB.
  • Code: 04
  • Display: PAPER JAM
  • Description: message appears when the paper jam has not occurred, and the printer cannot be in READY mode.
  • Remedy: 1. Registration paper sensor lever does not move smoothly, or is damaged. Action: Adjust the lever so that it moves smoothly. Replace it if damaged. 2. Pick-up unit sensor lever does not move smoothly, or is damaged. Action: Adjust the lever so that it moves smoothly. Replace it if damaged. 3. Fixing unit delivery sensor lever does not move smoothly, or is damaged. Action: Adjust the lever so that it moves smoothly. Replace it if damaged. 4. Face-down tray delivery sensor lever does not move smoothly, or is damaged. Action: Adjust the lever so that it moves smoothly. Replace it if damaged. 5. Sensor failure Action: Using the printer driver tester, check the condition of the sensors. If the LED of the tester does not light up when the sensor lever is shifted, replace the sensor.
  • Code: 05
  • Display: PRINTER OPEN
  • Description: message appears when the cover is closed.
  • Remedy: 1. The projection for the delivery cover is damaged. Action: Replace the delivery cover. 2. The projection for the upper cover is damaged. Action: Replace the upper cover. 3. The projection for the pick-up unit door is damaged. Action: Replace the pick-up unit door. 4. The pick-up unit door sensor is defective. Action: Using the printer driver tester, check the condition of the sensor. If the LED of the tester does not light up when the pick-up unit door is opened, replace the sensor. 5. Interlock arm does not move smoothly, or is damaged. Action: Adjust the arm so that it moves smoothly. Replace it if damaged. 6. Connector is loose. Action: Reconnect connector J1401 on the switch/sensor PCB and connectors J205 and J221 on the DC controller PCB. 7. The door switch is defective. Action: Replace the switch/sensor PCB. 8. The DC controller PCB is defective. Action: Replace the DC controller PCB.
  • Code: 10.1
  • Display: 10.1 ERROR FUSER CALL FOR SERVICE
  • Description: Fixing unit failure (abnormal low temperature
  • Remedy: 1. The rated voltage of the fixing unit installed in the printer differs from the line voltage. Action: Replace the fixing unit. 2. The thermistor is dirty. Action: If the thermistor contact area of the upper fixing roller is dirty, clean it. 3. The thermistor is not installed correctly. Action: If the thermistor is not evenly contacting the upper fixing roller, re-install the thermistor correctly. 4. The thermistor wire is broken. Action: Turn the power OFF and remove the fixing unit. Measure the resistance between the fixing unit connector J50B-5 (FSRTH) and J50B-4 (GNDTH). If the resistance is not between about 190kom and 290kom (room temperature of 25°C), check the wiring from connector J222 on the DC controller PCB to the thermistor. If it is normal, replace the thermistor. 5. The main heater wire is broken. Action: Remove the fixing unit. If there is no continuity between the fixing unit connector J50-3 (FSRN1: the upper right terminal of the left connector) and J51-5 (FSRN2: the upper right terminal of the right connector), replace the main heater. 6. The sub heater wire is broken. Action: Remove the fixing unit. If there is no continuity between the fixing unit connector J50-4 (FSRL1: the lower right terminal of the left connector) and J51-6 (FSRL2: the lower right terminal of the right connector), replace the sub heater. 7. The thermoswitch is open. Action: Remove the fixing unit and wiring cover. If there is no continuity between thermoswitch terminals, replace the thermoswitch. 8. The fixing unit drive circuit is defective. Action: Replace the power supply unit. 9. The DC controller PCB is defective. Action: Replace the DC controller PCB.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us